Will the Timbren part # TGMRTTK30 Fit my 1994 Chevrolet C/K 3500

Question

Question:

will this work for my truck ?

asked by: FRANK M

0

Expert Reply:

Yes the Timbren Rear Suspension Enhancement System part # TGMRTTK30 is a confirmed fit for your 1994 C/K 3500. They have been designed as a bolt on upgrade and will help take alot of wear and tear off of your rear suspension system.

expert reply by: Randy B

0

Answer 1

Yes, there are spacers that can be used with the Timbren #TGMRTTK30 kit on your 1987 GMC Pickup with a 2-1/2" lift. We recommend using two of the 1" spacers #TA25723-90AD00 on each side. The idea is to have a 1/2" to 1-1/2" gap…

view full answer...

Answer 2

The overall height of the Timbren Rear Suspension Enhancement System #TGMRTTK30 is 7-1/8 inches.

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 5

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 6

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 7

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 8

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 9

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 10

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 11

If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…

view full answer...

Answer 12

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Will the Timbren part # TGMRTTK30 Fit my 1994 Chevrolet C/K 3500

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching