Will the Stromberg Carlson 100 Series 5th Wheel Tail Gate VGD-94-101 Fit a 2001 Dodge Ram D2500

Question

Question:

Will this vented tailgate, VGD-94-101, fit on a 2001 Dodge, D2500, diesel pickup?

asked by: Janet R

0

Expert Reply:

I spoke with my contact at Stromberg Carlson. The 5th wheel tail gate, # VGD-94-101, will fit the 2001 Dodge Ram D2500 as long as it does not have a flare side/step side bed. If your bed is in anyway wider or more narrow than the standard bed, it will not fit. The length of the bed does not matter.

expert reply by: Michael H

0

Answer 1

The Stromberg Carlson 100 Series 5th Wheel Tailgate with Open Design for Dodge Trucks #VGD-94-101 comes with most of the hardware needed for installation on your 2001 Dodge Ram 2500. For some reason it seems they don't give you the additional 4…

view full answer...

Answer 2

The replacement tailgates like the #VGD-94-101 install pretty easily. Basically you would just need to remove your current tailgate. What you would need to do is lower the tailgate to about a 45 degree angle so that you can lift the tailgate off of…

view full answer...

Answer 3

I do have an option for you, but we do not carry the Dexter 072-027-00 you mentioned. However we do have the etrailer Double-Eye Spring for 7,000-lb Trailer Axles - 24-7/8" Long #e64SR which will be 3/8" shorter but that is still close…

view full answer...

Answer 4

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 5

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 6

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 7

Yes, you are correct. In order to correctly take this measurement you will need to measure from the center of the spindle to the center of the main axle tube. I have included a picture for reference.

view full answer...

Answer 8

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 9

The #99 trailer spindle is typically found on 9,000 lb and 10,000 lb axles. This is not a spindle that we carry at this time, but I did find some of the measurements. I have attached a diagram showing the dimensions of a #99 spindle for you to check…

view full answer...

Answer 10

In order to charge your batteries wired in parallel with the NoCo Genius #329-GENIUS5 you'll want to connect the positive charge line to the positive terminal of the first battery and the negative line to the negative terminal of the opposite…

view full answer...

Answer 11

According to my contact at Fantastic Vent the correct replacement lift motor to use in your vent is part #FVK6010-81, not item FVK-6050-80. The replacement motor does operate at a higher 17-RPM speed. Since your fan is of a lower rpm and manufactured…

view full answer...

Answer 12

The DeeMaxx item #DE86VR won't because of the spacing on the mounting bracket but I have a caliper that will. To replace your Tie Down Engineering 46304 caliper you will need the Kodiak Disc Brake Caliper item #KDBC225DAC.

view full answer...

Will the Stromberg Carlson 100 Series 5th Wheel Tail Gate VGD-94-101 Fit a 2001 Dodge Ram D2500

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching