What is Size of Fulton Winch part # F142102

Question

Question:

What is the physical size of the winch, LxWxH?

asked by: Mark

0

Expert Reply:

The height of the Fulton winch part # F142102 is 6 inches, the width is 5-1/4 inches without the handle and then with the handle is 10 inches. The length front to back is 7 inches.

expert reply by: Jameson C

0

Answer 1

The 4-Leaf Slipper Spring w/ Radius End for 2,000-lb Trailer Axles #e69SR should be compressed ~2" under a 1,000 lb load which would make the "F" measurement ~1 3/4" with the 1,000 lb load. This is based on a formula to find…

view full answer...

Answer 2

The Fulton Single Speed Trailer Winch part #F142102 uses a standard winch mounting pattern which I have attached a photo of for you. If your winch mounting pattern does not match this then your would be best off to just re-drill as most boat trailer…

view full answer...

Answer 3

The bolts for the mounting hardware that comes with the Round Swivel Marine Jack w/ Wheel #MJ-1500B have an overall length of 4 1/4" and the thread is 3/8-16 course threaded. If you are needing new hardware for this jack then we actually have…

view full answer...

Answer 4

When comparing the 1.3K Dutton-Lainson Hand Winch #DL14362 and the 1.3K Fulton Single Speed Winch #F142104, I recommend the Fulton option because it has a long salt spray rating at 600 hours for the Z-Max. Aside from the manufacturer and coatings…

view full answer...

Answer 5

It can be a flat end as long as the flat part is long enough that it can reach past the wet bolt just fine. For your application it looks like the 4-Leaf Slipper Spring w/ Radius End for 2,000-lb Trailer Axles #e69SR is the closest that we have as…

view full answer...

Answer 6

The Round Swivel Marine Jack #MJ-1500B-DWL is roughly 25" total in length with the jack fully retracted. I've linked a diagram that shows the other important measurements that you might be interested in, as well.

view full answer...

Answer 7

Yes, the Fulton Single Speed Trailer Winch #F142102 can be used with 5/16" wire rope that is a maximum of 30' long. I've left a link to a video review of this product for you to take a look at.

view full answer...

Answer 8

The mounting bracket on the Fulton Single Speed Trailer Winch #F142002 is 3-5/8" wide, so it's going to be fairly close to your original bracket.

view full answer...

Answer 9

It's pretty easy to determine the correct replacement leaf springs for your trailers, and there's different ways for double-eye springs and slipper springs. You do have to account for the sag, so go with ones that measure shorter than what…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Answer 12

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

What is Size of Fulton Winch part # F142102

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching