Bolt Thread Size of Mounting Hardware for etrailer Round Swivel Marine Jack w/ Wheel

Question

Question:

Hi, Whats the bolt thread size and length?

asked by: Victor

0

Expert Reply:

The bolts for the mounting hardware that comes with the Round Swivel Marine Jack w/ Wheel # MJ-1500B have an overall length of 4 1/4" and the thread is 3/8-16 course threaded.

If you are needing new hardware for this jack then we actually have that available as part # MJ-1000B-MBB.

expert reply by: Jon G

0

Answer 1

The 4-Leaf Slipper Spring w/ Radius End for 2,000-lb Trailer Axles #e69SR should be compressed ~2" under a 1,000 lb load which would make the "F" measurement ~1 3/4" with the 1,000 lb load. This is based on a…

view full answer...

Answer 2

To choose a compatible hub assembly for any spindle the key is knowing the inner and outer bearing part numbers, or if they are not available, precise dimensions of the spindle at the points where the bearings and grease seal ride. These points on…

view full answer...

Answer 3

It's pretty easy to determine the correct replacement leaf springs for your trailers, and there's different ways for double-eye springs and slipper springs. You do have to account for the sag, so go with ones that measure shorter than…

view full answer...

Answer 4

It can be a flat end as long as the flat part is long enough that it can reach past the wet bolt just fine. For your application it looks like the 4-Leaf Slipper Spring w/ Radius End for 2,000-lb Trailer Axles #e69SR is the closest that we have as…

view full answer...

Answer 5

The Round Swivel Marine Jack #MJ-1500B-DWL is roughly 25" total in length with the jack fully retracted. I've linked a diagram that shows the other important measurements that you might be interested in, as well.

view full answer...

Answer 6

The mounting bracket on the Fulton Single Speed Trailer Winch #F142002 is 3-5/8" wide, so it's going to be fairly close to your original bracket.

view full answer...

Answer 7

For your 2.5 inch wide and 2 inch high trailer tongue, the Round Swivel Marine Jack w/ Wheel - Bolt On - Zinc - Sidewind - 11" Travel - 1,500 lbs #MJ-1500B is my recommendation. It will work very well with the trailer tongue you have and will…

view full answer...

Answer 8

We do have the correct replacement inner member for your LP7500 actuator, which is the following part: - Replacement Inner Member for Dexter DX7.5L Actuator - Single Axle with Disc - 2" Ball - 7,500 lbs #DX39FR This is the replacement for both…

view full answer...

Answer 9

The 3,200 lb 2-Speed Boat Trailer Winch with 20' Strap and Brake #315-W3200D will be sufficient to pull in your 3,190 lb boat if your trailer has rollers on it as that will make your boat easier to move. If you have bunks then it will technically…

view full answer...

Answer 10

With a few possible exceptions (large fifth wheels that use LT or Light Truck Tires), we recommended that only trailer tires be used on trailers because they have stiffer sidewalls which do a better job dealing with the vertical load tires experience…

view full answer...

Answer 11

The 15x6 inch wheel #AM20535 will accept 205/75-15 tires, 225/75-15 tires, and 7.00-15LT tires. I have linked the 15 inch tires we carry for you. For a valve stem you can use #AM20904.

view full answer...

Answer 12

There will not be much difference in ride smoothness between a fully-inflated 35-psi rated tire and a fully-inflated 90-psi rated tire, but typically a radial will give a slightly smoother ride than a bias ply tire since it has a more flexible…

view full answer...

Bolt Thread Size of Mounting Hardware for etrailer Round Swivel Marine Jack w/ Wheel

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching