Will 5-7/16" Tall Center Hanger for Double-Eye Springs Work with 9/16" Bolt

Question

Question:

The dimensions of the 5 7/16 tall suspension brackets are perfect but I need it with a 9/16th bolt hole instead of 3/4- do you have that?

asked by: Nico B

0

Expert Reply:

Even though the 5-7/16" Tall Center Hanger for Double-Eye Springs # 115919 has a 3/4" diameter bolt hole, this is actually designed to work with 1-3/4" wide double-eye leaf springs that install using 9/16" diameter bolts which I think is what you're getting at, so this should work perfectly for your application!

If you check out the Tandem-Axle Trailer Hanger Kit for Double-Eye Springs # APT4 you can see where these same hangers are used in a kit that comes with 9/16" bolts so having that hole a little larger on the hanger is completely acceptable.

expert reply by: Jon G

0

Answer 1

The shock kit will do the best at preventing the bouncing since they dampen the movement of the suspension which slows it down. This is why vehicle suspension does not bounce like trailer suspension since vehicles have shocks/struts. If you have a…

view full answer...

Answer 2

Before replacing the wet bolt I would make sure that the hole on the zerk fitting is pointed sideways, as that might be why it's not taking any grease. If you do need to replace the bolt you'll need a 9/16" bolt that's roughly…

view full answer...

Answer 3

If the outside width of hanger #E4139 is 2-5/16 inches and the metal thickness is 3/16 of an inch then you would take 2-5/16 and subtract 3/16, and then subtract another 3/16, to get 1-15/16 inches. It is meant to be used with leaf springs that are…

view full answer...

Answer 4

I have a solution for you to get a powered awning on your coach, and the Solera 12V Power RV Awning Conversion Kit - Universal - 69" Arms - White #LC434724 wouldn't necessarily have any issues holding the weight of an awning that size.…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

I do have an option for you, but we do not carry the Dexter 072-027-00 you mentioned. However we do have the etrailer Double-Eye Spring for 7,000-lb Trailer Axles - 24-7/8" Long #e64SR which will be 3/8" shorter but that is still close…

view full answer...

Answer 7

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 8

I've actually answered a similar question on this before and found: In my research I found that the grease seal you are looking for could have an inner diameter of either 2.24 or 2.12 inches and an outer diameter of 3.37 inches when measured with…

view full answer...

Answer 9

According to my contact at Fantastic Vent the correct replacement lift motor to use in your vent is part #FVK6010-81, not item FVK-6050-80. The replacement motor does operate at a higher 17-RPM speed. Since your fan is of a lower rpm and manufactured…

view full answer...

Answer 10

The #99 trailer spindle is typically found on 9,000 lb and 10,000 lb axles. This is not a spindle that we carry at this time, but I did find some of the measurements. I have attached a diagram showing the dimensions of a #99 spindle for you to check…

view full answer...

Answer 11

In order to charge your batteries wired in parallel with the NoCo Genius #329-GENIUS5 you'll want to connect the positive charge line to the positive terminal of the first battery and the negative line to the negative terminal of the opposite…

view full answer...

Answer 12

Yes, you can use the NOCO GEN On-Board Battery Charger #NOC34FR on your pickup's parallel batteries without disconnecting them. If your batteries were in a series, they would have to be disconnected. Since your batteries are parallel and maintain…

view full answer...

Will 5-7/16" Tall Center Hanger for Double-Eye Springs Work with 9/16" Bolt

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching