Where Are the etrailer Scissor Stabilizer Jacks Made

Question

Question:

Is this made in America?

asked by: Annmarie T

0

Expert Reply:

The majority if not all of the Scissor Stabilizer Jacks like part # TJSC-24 are going to be made overseas. That said, this is not a sign of poor quality because if you look at the reviews you will see a reflection of a quality well made product. If interested, we also have other options with more lift such as ones from Ultra-Fab part # UF48-979006, Lippert part # LC285325, and Stromberg Carlson part # JSC-24-IND.

expert reply by: Conner L

0

Answer 1

The R-Pod 180 that you have has scissor jacks attached to the frame in all four corners of the trailer. Since it looks like your trailer sits pretty high off of the ground the pair of jacks I recommend are the Ultra Fab #UF48-979031 which have 30…

view full answer...

Answer 2

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 3

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 6

The Bargman 7-Way, RV-Style Connector #WG54006-043 referenced in your question uses the standard RV-style pin locations for its 7-Way connector. I have attached a diagram of these locations and their functions for you to check out. Wire colors will…

view full answer...

Answer 7

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 8

The Replacement Amber Lens for MC32AB Trailer Lights #A32AB is a direct replacement for the SAE A P2 DOT 14 and would be what you'd need.

view full answer...

Answer 9

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 10

The best modern day size replacement option we have for a 6.00-16 is a 235/80-16 which measures 30-7/8" diameter x 9-3/8" wide. For this, I recommend the Kenda Karrier ST235/80R16 Radial Trailer Tire with 16" Black Mod Wheel part…

view full answer...

Answer 11

The Trailer Leaf Spring, 2250 lbs. 6 Leaf, item #e27SR, is sold as a replacement spring for older trailers and measures 26 inches for eye to eye, center to center. If you are replacing the springs and hangers you will need to use the same center to…

view full answer...

Answer 12

The 18.5x8.5-8 is actually an old tire size that is not used much anymore. The closest metric size to your existing tire would be 215/60-8. Your wheel most likely has a 5-on 4-1/4 inch bolt pattern (see link), you will want to make sure that the bolt…

view full answer...

Where Are the etrailer Scissor Stabilizer Jacks Made

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching