Recommended Trailer Leaf Spring Mounts
Question:
I want to replace leaf springs and mounts. As you can see from picture the prior mounts were welded to angle iron and bolted to side of trailer. Is this the best option going forward? Any advantage or disadvantage to welding mounts directly to trailer frame? Or should I drill holes in bottom of trailer frame and bolt mounts to trailer? Thanks
asked by: Wallace T
Helpful Expert Reply:
You are on the right track here! I recommend welding them to the trailer this is the most common practice and will prove to be the most reliable. The 4-Leaf Double-Eye Spring for 3,500-lb Trailer Axles part # e54SR that you looked at are 1 3/4" wide with that said and looking at the photo I recommend going with the Front/Center/Rear Hanger for Double-Eye part # 115918 This has the width and bolt eye diameter you want.
If you will need the bolt to connect the two together use the Zinc Shackle Bolt with Locknut for Double-Eye Springs part # TRFA73Z916DLNZ
Products Referenced in This Question
Front/Center/Rear Hanger for Double-Eye Springs - 2-3/8" Tall - 9/16" Bolt Hole
- Trailer Leaf Spring Suspension
- Hangers
- Camper
- Car Hauler
- Utility Trailer
- Double Eye Springs
- 9/16 Inch Diameter
- 2-1/2 Inch Tall
- Tandem Axle
- Triple Axle
- etrailer
more information >
Zinc Shackle Bolt with Locknut for Double-Eye Springs - 3" Long
- Trailer Leaf Spring Suspension
- Suspension Bolts
- Boat Trailer
- Snowmobile Trailer
- 9/16 Inch Diameter
- 3 Inch Long
- TruRyde
more information >
Product Page this Question was Asked From
4-Leaf Double-Eye Spring for 3,500-lb Trailer Axles - 25-1/8" Long
- Trailer Leaf Springs
- Double Eye Springs
- 3500 lbs
- 1-3/4 Inch Wide
- 4 Leaf
- 25-1/8 Inch Long
- Painted
- etrailer
more information >
Continue Researching
- Video: Redline Trailer Suspension 166081 Review
- Shop: Front/Center/Rear Hanger for Double-Eye Springs - 2-3/8" Tall - 9/16" Bolt Hole
- Shop: Wet Equalizer Bolt with Locknut and Grease Zerk for Double-Eye Springs - 3" Long
- Shop: Shackle Bolt with Locknut for Double-Eye Springs - 3" Long
- Shop: Dexter Bronze Bushings - Qty 4
- Video: Review of etrailer Trailer Leaf Spring Suspension - Hanger For Double Eye Spring - 115918
- Video: Review of TruRyde Trailer Leaf Spring Suspension - Suspension Bolt and Locknut - TRFA73Z916DLNZ
- Q&A: Recommended Leaf Spring Bushings and Shackle Bolt with Locknut
- Shop: Zinc Shackle Bolt with Locknut for Double-Eye Springs - 3" Long
- Shop: Front/Center/Rear Hanger for Double-Eye Springs - 4-1/4" Tall - 9/16" Bolt Hole
- Q&A: What Is The Difference Between Different Sized Hangers, Equalizers, And Shackle Straps
- Video: Dexter Bronze Bushings Installation - 2019 CrossRoads Redwood Fifth Wheel
- Shop: Tandem-Axle Trailer Hanger Kit for Double-Eye Springs - 1-1/2" Front/Rear, 2-1/2" Center
- Shop: Suspension Enhancement
- Article: Double-Eye Trailer Suspension System Review
- Search Results: equalizer
- Shop: Trailer Hitch
- Article: How to Accurately Measure Trailer Leaf Springs
- Search Results: leaf spring
- Shop: Trailer Wiring
- Search Results: leafsprings
- Video: MORryde Tandem Axle Trailer Suspension Upgrade Kit Installation
- Article: How to Raise Your Travel Trailer Height
- Shop: Brake Controller
- Search Results: morryde
- Article: 5 Tell-Tale Signs It’s Time to Replace Your Trailer’s Leaf Springs
- Search Results: trailer leaf springs
- Video: Review of MORryde Trailer Leaf Spring Suspension - Spring Mounting Hardware - MR46ZR
- Article: Trailer Tire Sizing
- Shop: Gooseneck Hitch