How Can I Make My Trailer Jack Stand Taller

Question

Question:

Is there anything taller than this? I have my tongue jack fully extended with over 8inch of blocks under the jack and still having a hard time removing my WDH bars.

asked by: Ron

0

Expert Reply:

I have a solution for you, but the Valterra # A10-0900 is going to be the tallest jack stand that we have available. I recommend using one or two of the Stackers Leveling Block # A10-0917 under this jack stand to give you enough clearance to easily release the tension bars and remove them from your weight distribution hitch. You can also get a pack of 10 Stackers Leveling Blocks with part # A10-0918. Each Stacker Leveling Block will add 1-3/8" of lift to your jack stand.

expert reply by: Erik B

0

Answer 1

You are correct about the small depression in the Valterra Trailer Jack Stand #A10-0900. The unit stands 8-3/8" tall, but the depression where the trailer jack sits is approximately 1" deep so that means the jack stand will add…

view full answer...

Answer 2

Each of the leveling blocks we carry have a width between 8-1/4 inches, such as the Ultra-Fab #UF48-979052 you mentioned, and 8-1/2 inches, such as the Stackers #A10-0918. The Stackers have a 40,000 lbs gross vehicle weight capacity and can be used…

view full answer...

Answer 3

Whether you are using just 1 or all 10 of the Stackers Leveling Blocks #A10-0918 the maximum capacity is 40,000 pounds.

view full answer...

Answer 4

With the 10 blocks that come with the Stackers Multi-Use Wheel Supports #A10-0918 that you referenced the overall height max when using them with 4 pads is going to be right at 4-1/2 inches. I attached a picture that shows this used in that…

view full answer...

Answer 5

I think you are going in the right direction. I would definitely replace the 14 gauge wire going to the trailer brake magnets with 10 gauge wire or larger. Usually larger than 10 gauge is hard to get into the trailer connector though. I would also…

view full answer...

Answer 6

To wire your electric brakes you will want to run 10 gauge wire #10-1-1 to one of the brakes and run it to the other brake, using butt connectors like #05732-2 to connect them. The grounds will not be spliced, each brake assembly should have its own…

view full answer...

Answer 7

To help prevent the sway you are experiencing on your 2019 Ford F-250 you will want to add a sway bar. The Roadmaster Rear Anti-Sway Bar #RM93VR is for trucks that have the forward leaf spring bump pads bolted on to the frame. If yours are Riveted…

view full answer...

Answer 8

The installation instructions for this product are recommended for individuals who have experience winding torsion springs. If you have not worked with a torsion spring system before, we recommend contacting a local garage door company to install…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

The Hellwig Adjustable Big Wig Rear Anti-Sway Bar #HE94FR is only going to leave a few inches between it and the spare tire, as you can see in the attached picture. Depending on how far forward you have the tire it could potentially interfere with…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...