Max Height of the Stackers Multi-Use Wheel Supports # A10-0918

Question

Question:

On Part# Item # A10-0918 - what is the maximum height you can stack the leveling block

asked by: Jeff H

0

Expert Reply:

With the 10 blocks that come with the Stackers Multi-Use Wheel Supports # A10-0918 that you referenced the overall height max when using them with 4 pads is going to be right at 4-1/2 inches.

I attached a picture that shows this used in that configuration.

expert reply by: Jameson C

0

click to enlarge

Answer 1

Whether you are using just 1 or all 10 of the Stackers Leveling Blocks #A10-0918 the maximum capacity is 40,000 pounds.

view full answer...

Answer 2

Each of the leveling blocks we carry have a width between 8-1/4 inches, such as the Ultra-Fab #UF48-979052 you mentioned, and 8-1/2 inches, such as the Stackers #A10-0918. The Stackers have a 40,000 lbs gross vehicle weight capacity and can be used…

view full answer...

Answer 3

I believe you're looking for something like the Lippert 3.0 Ground Control 3.0 system. Unfortunately, Ultra-Fab doesn't offer a product that would allow you to individually control 4 separate jacks. The only product we offer that would do…

view full answer...

Answer 4

I spoke with my contact at Andersen regarding the Camper Wheel Chock and Leveler #AM3604 referenced in your question. He stated that while the levelers are designed to work with most tandem axle setups, there are rare instances like yours where the…

view full answer...

Answer 5

Camper leveling blocks like the Camco FasTen RV Leveling Blocks #CAM44515 are a good choice for leveling an RV with dually rear wheels. It is okay to place a leveler under only one of the dually tires but using larger blocks like the Camco #CAM44525…

view full answer...

Answer 6

The Lynx Leveling Blocks you have will not work with the Ultra-Fab Leveling Blocks part #UF48-979051. The reason for this is that the surface pattern which is used to lock them together is different. You would need to either purchase more of the Lynx…

view full answer...

Answer 7

While you can install a Safety Step Sand Away Dirt Trapping Step Cover #SASSA11-00 on each step, you can only leave it on the bottom step when the steps are closed. The middle step covers would need to be removed for the steps to retract. You could…

view full answer...

Answer 8

You are correct about the small depression in the Valterra Trailer Jack Stand #A10-0900. The unit stands 8-3/8" tall, but the depression where the trailer jack sits is approximately 1" deep so that means the jack stand will add…

view full answer...

Answer 9

I have a solution for you, but the Valterra #A10-0900 is going to be the tallest jack stand that we have available. I recommend using one or two of the Stackers Leveling Block #A10-0917 under this jack stand to give you enough clearance to easily…

view full answer...

Answer 10

The installation instructions for this product are recommended for individuals who have experience winding torsion springs. If you have not worked with a torsion spring system before, we recommend contacting a local garage door company to install…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Max Height of the Stackers Multi-Use Wheel Supports # A10-0918

Product Page this Question was Asked From

Continue Researching