What are the Cut Outs for on the Back of Trailer Fender # PF11X35W-2

Question

Question:

Do these fenders have cut-outs for clearance lights like the Fulton? If yes, what LED lights fit in there? Thank you!

asked by: Juergen

0

Expert Reply:

If you look at some of the other pictures of Fender # PF11X35W-2 you will see that it has somewhat of a cut out on either side at the back but they are for the included mounting brackets. The same goes for the Fulton fenders but they do not come with mounting brackets.

Clearance lights can be surface mounted to the outside of the fenders. Rectangular lights measuring from 2-1/2 to 4 inches long seem to be the most popular for this application.

expert reply by: Michael H

0

Answer 1

The included hardware that comes with the Plastic, Single-Axle Trailer Fenders #PF11X35W-2 is the Galvanized Steel, U-Shaped, Bolt-On Brackets #PF1135-BKT-2. I attached a couple pictures of the brackets for you to check out also.

view full answer...

Answer 2

Since Spartan went out of business I wouldn't be able to get an exact part number for you but I can help you find a replacement. When it comes to choosing the correct replacement fender a lot of it depends on what size wheels you are using and…

view full answer...

Answer 3

The Single Axle Trailer Fenders w Mounting Brackets - White Plastic - 13" to 15" Wheels #PF11X35W-2 comes with the mounting brackets to stabilize the fender. You do not need to drill into the backing for that installation. If you choose to…

view full answer...

Answer 4

I was able to find photos of Escort single-axle boat trailers with the top/side step fenders. The fenders that we offer that have top/side steps are all plastic units which can be seen on the link provided. Installation brackets are not included with…

view full answer...

Answer 5

Most likely the correct replacement bearing buddy bra that you would need is the part #BB19B which has an outer diameter of 2-1/8 inches. Part #BB17B has an outer diameter of 2 inches, and part #BB23B has an outer diameter of 2.441 inches (this would…

view full answer...

Answer 6

We offer replacement bras for Bearing Buddy grease caps in three sizes, parts #BB23B, #BB19B and #BB17B. These have outer diameters of 2-7/16-inch, 2-1/8-inch and 2-inches, respectively. The specific protectors these fit are shown on each item's…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 12

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...