Replacement Clamp Kit for Truxedo Lo Pro Tonneau Cover

Question

Question:

I have a 2014 gmc Sierra with the truxedo lo pro tonneau cover. Will these work on it?

asked by: Adam M

0

Expert Reply:

Truxedo has a replacement clamp kit for the Truxedo Lo Pro Tonneaus with the part # TX1117819 which would be what you'd need.

expert reply by: Jameson C

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 3

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 8

To utilize the Titan Chain Sliding Lashing Winch for Flatbed Truck or Trailer #TCLR900 you need the following: - Brophy Winch Bar for 2" Lashing Winch #W2BZ - etrailer Sliding Winch Track #e48ZR

view full answer...

Answer 9

Hey Jeff, The Pace Edwards JackRabbit Retractable Hard Tonneau Cover w Explorer Rails #311-JED7833 is designed for a 6-1/2' bed while the #311-KRD7936 is designed for an 8' bed. Since you have a 6-1/2' bed the #311-JED7833 would be the…

view full answer...

Answer 10

You do not need to remove the bed of your truck to install the HappiJac part #LC182906-182971 that you referenced. I found a copy of the install instructions for this part number (see attached pictures) and there's no mention of the bed needing…

view full answer...

Answer 11

Thanks for reaching out, Joe! I recommend using the Rhino-Rack Aero Bar Roof Rack for Camper Shells #Y02-480B which comes with 63" long tracks as well as 54" long crossbars which should give you a little bit of overhang on your canopy. Per…

view full answer...

Answer 12

I attached a picture to this page that has a wiring diagram for the Furrion Indoor Enclosed Amplified Subwoofer #FSW8P12CF that you referenced. I attached a review video for this for you to check out as well.

view full answer...