Is Andersen Ultimate Fifth Wheel Adapter Compatible with Morryde Pin Box

Question

Question:

Will my existing Anderson hitch work with or need any additional parts in order to use on my new Morryde RPB72-1716 box?

asked by: Wayne H

1

Helpful Expert Reply:

The Andersen Ultimate fifth wheel adapter part # AM3200 that you referenced is perfectly compatible with the Morryde pin box RPB72-1716 that you referenced.

expert reply by: Jameson C

1

Answer 1

Yes we do have exactly what you're looking for! The 5th-Wheel-to-Gooseneck Coupler Adapter Mounting Plate for MORryde Pin Boxes #MR37ZR is the MORryde RPB77-006 adapter that you're looking for.

view full answer...

Answer 2

You can use the Andersen Ultimate Connection 5th Wheel Trailer Hitch System, part #AM3200 with your 5th Airborne pin box on your fifth wheel trailer.

view full answer...

Answer 3

There are a few ways to determine the axle capacity on your Jayco 5th wheel trailer. The trailer's main identification plate will often indicate axle ratings along with gross vehicle weight (GVWR) and the unit's VIN. This plate will typically…

view full answer...

Answer 4

I have a couple solutions for you. You can use the A-iPower 3,800-Watt Portable Inverter Generators - 3,000 Running Watts - Gas - Manual Start #289-SUA2000i-2. It can power one 15,000 BTU AC unit and run one or two other appliances at the same time.…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 7

Great question, Jeff! When the Rota-Flex first came out it renovated what a pin box could do and be, but at this point in time that technology is a little more dated and the Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #325-GH-8040 is the "new…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

Beds shorter than 8 foot do commonly need a slider hitch David, but a lot of modern fifth wheel trailers are now made with tapered noses to help and in a lot of cases a slider isn't required. So if the trailer you plan to tow has a tapered nose…

view full answer...

Answer 10

You do not have to use a sliding 5th wheel hitch in a short bed truck. In many cases, truck beds shorter than 8 ft do not have enough clearance between the trailer and truck to execute sharp turns. This is why sliding hitches were invented. Due to…

view full answer...

Answer 11

The Ram OEM 5th wheel puck system, shown in the linked photo and article, was launched in 2013 so what you have in your truck is likely to be an aftermarket installation of some kind. These newer Ram trucks with the factory prep can directly accept a…

view full answer...

Answer 12

As far as height adjustability and weight capacities the Curt Q20 #C16130 and the Curt A20 #C16140 are identical. They both have a Gross Towing Weight of 20,000 lbs, a Vertical Load Limit of 5,000 lbs, and a height range of 13-17 inches. When it…

view full answer...

Is Andersen Ultimate Fifth Wheel Adapter Compatible with Morryde Pin Box

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching