Can The Handle Of The Titan Breakaway Parking Kit Be Installed on the Side Of Shorter Trailer Tongue

Question

Question:

Hi I am building a camper and would like to install a parking brake. I am using 4inch square tubing for the tongue and do not have that much room left on it. How long is the handle assembly and can it be mounted on the side of the tongue?

asked by: Michael H

0

Expert Reply:

I contacted Titan and you can install the lever of the Titan Breakaway and Parking Kit for Drum Brakes part # T2385200 to the side of the tongue as long as you keep the cables straight to be able to activate the breakaway if the trailer disconnects. The bracket for the lever (that part that attaches to the trailer tongue) is about 10" long.

You do want to be sure your braking assemblies are equipped to add a parking kit. If you take a look at the backing plate of your assemblies there should be an actuating lever at the top of the assembly that you attach the parking brake cable too. I have attached a photo for your reference. If you do not have these levers you will need different braking assemblies. If you let me know the diameter of your assemblies and your axle capacity I can make a recommendation.

expert reply by: Heather A

0

click to enlarge

Answer 1

I attached a diagram that shows how the parking brake kit for trailers part #T2385200 installs on a trailer. You can see where it attaches on the trailer tongue as well as how it interacts with the other components of the trailer.

view full answer...

Answer 2

To use a hand brake like the part #T2385200 with the Timbren system part #ASR35HDS02 that you referenced you will need to use a hydraulic drum brake with a parking brake linkage. Since the recommended hub/drum is the part #8-201-9UC3-EZ which is a…

view full answer...

Answer 3

There isn't a specific owners manual for your Dexter Hydraulic Brake Kit #T2351300-200. This system simply uses the Titan Breakaway and Parking Kit for Drum Brakes #T2385200 which will install based on the photo I've attached.…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 7

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 8

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

Typically 4-way wiring consists of 18 and 16 gauge wires. For a 4-way that has all 16 gauge wire you would want the Wesbar 4-Pole Flat Connector #W787264. The part #HM38138 uses 18 gauge for all wires but the white that uses 16 gauge.

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...