What Is The Difference In The B&W Biker Bars

Question

Question:

What is the difference in this bar for a 2016 Fat Boy compared to the one for touring bikes Roadglide they look the same

asked by: Bruce

0

Expert Reply:

The Replacement Bar for B&W Biker Bar Motorcycle Tie-Down System # BWMC2302B fits the frame diameter of 1.250" to 1.375" and width 10" to 14.5" softail bikes.

The B&W Biker Bar Motorcycle Tie-Down System for Trailers # BWMC2301 fits the frame diameter 1.125" to 1.250" and width 10" to 14.5" of touring bikes. While the bars appear similar they are designed to fit different bike dimensions.

expert reply by: Patrick R

0

Answer 1

The B&W Biker Bar that you should be using for your 2010 Ultra Classic is the part #BWMC2301 but for your 2014 Softail Deluxe you need the Biker Bar #BWMC2302 instead. Good news is that both options use the same base system so you just need…

view full answer...

Answer 2

That will depend on which model B&W Biker Bar Motorcycle Tie-Down System you have installed on the trailer. The #BWMC2301 will only work with touring bikes and the 2016 Fat Boy would be considered a softail and needs the #BWMC2302. You can…

view full answer...

Answer 3

The Replacement Bar for B&W Biker Bar Motorcycle Tie-Down System #BWMC2302B is the replacement bar that fits H-D Dyna, Softail, and V-Rod bike frames. The #BWMC2301B is the Replacement Clamping Bar for B&W Biker Bar Motorcycle…

view full answer...

Answer 4

Actually yes. All of the Biker Bars use the same base, #BWMC2300. The clamping bar for touring bikes is #BWMC2301B and for the Heritage bikes the bar is #BWMC2302B.

view full answer...

Answer 5

I checked with B and W to find out how to tell the two Biker Bars you have apart and they told me that the #BWMC2301 has black pads where it grabs the frame and the part #BWMC2302 has gray pads. While she didn't specify what the overall…

view full answer...

Answer 6

I checked with B and W and the Biker Bar part #BWMC2300 would work well on your 2016 Harley CVO Breakout. They state that this fits all Harleys that have painted frames like what your bike has so it would work well.

view full answer...

Answer 7

The 2003 Harley Heritage Springer would fall into the Softail, Dyna, and V-Rod category as far as the Bike Bars go so you would need model #BWMC2302. Specs on this model are: Fits frame tube diameters between 1-1/4" - 1-3/8" Fits frame…

view full answer...

Answer 8

For your 2010 Harley-Davidson Fat Boy Lo FLSTFB bike, the B&W Biker Bar Motorcycle Tie-Down System, #BWMC2302, will work well for this bike. The Biker Bar will fit up against the frame tubes of your Fat Boy to secure the bike on a open or…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

What Is The Difference In The B&W Biker Bars

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching