B and W Biker Bar Recommendation for 2016 Harley CVO Breakout

Question

Question:

Which should I order for a 2016 CVO Breakout?

asked by: Chad T

0

Expert Reply:

I checked with B and W and the Biker Bar part # BWMC2300 would work well on your 2016 Harley CVO Breakout. They state that this fits all Harleys that have painted frames like what your bike has so it would work well.

expert reply by: Jameson C

0

Answer 1

There's no reason a Biker Bar like the #BWMC2300 couldn't be used in a Kendon folding trailer like you mentioned.

view full answer...

Answer 2

The Replacement Bar for B&W Biker Bar Motorcycle Tie-Down System #BWMC2302B fits the frame diameter of 1.250" to 1.375" and width 10" to 14.5" softail bikes. The B&W Biker Bar Motorcycle Tie-Down System for Trailers…

view full answer...

Answer 3

The 2003 Harley Heritage Springer would fall into the Softail, Dyna, and V-Rod category as far as the Bike Bars go so you would need model #BWMC2302. Specs on this model are: Fits frame tube diameters between 1-1/4" - 1-3/8" Fits frame…

view full answer...

Answer 4

We sure do! The part number you're looking for is #BWMC2305, which provides a pair of anchor plates.

view full answer...

Answer 5

I reached out to B&W about your #BWMC2301 and they said you need to take the kick stand and kick it out and over the bar itself. The kick stand is spring loaded and will move right over the bar. It should work with no problem. Generally you can…

view full answer...

Answer 6

That will depend on which model B&W Biker Bar Motorcycle Tie-Down System you have installed on the trailer. The #BWMC2301 will only work with touring bikes and the 2016 Fat Boy would be considered a softail and needs the #BWMC2302. You can…

view full answer...

Answer 7

I checked with B and W to find out how to tell the two Biker Bars you have apart and they told me that the #BWMC2301 has black pads where it grabs the frame and the part #BWMC2302 has gray pads. While she didn't specify what the overall…

view full answer...

Answer 8

For your 2010 Harley-Davidson Fat Boy Lo FLSTFB bike, the B&W Biker Bar Motorcycle Tie-Down System, #BWMC2302, will work well for this bike. The Biker Bar will fit up against the frame tubes of your Fat Boy to secure the bike on a open or…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 12

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...

B and W Biker Bar Recommendation for 2016 Harley CVO Breakout

Product Page this Question was Asked From

Continue Researching