B&W Biker Bar for a 2003 Harley Davidson Heritage Springer

Question

Question:

What model of the BandW Biker Bar will fit my 2003 HD Heritage Springer? Thanks.

asked by: Rick C

0

Expert Reply:

The 2003 Harley Heritage Springer would fall into the Softail, Dyna, and V-Rod category as far as the Bike Bars go so you would need model # BWMC2302.

Specs on this model are:

Fits frame tube diameters between 1-1/4" - 1-3/8"
Fits frame width between 10" - 14"

expert reply by: Michael H

0

Answer 1

For your 2010 Harley-Davidson Fat Boy Lo FLSTFB bike, the B&W Biker Bar Motorcycle Tie-Down System, #BWMC2302, will work well for this bike. The Biker Bar will fit up against the frame tubes of your Fat Boy to secure the bike on a open or…

view full answer...

Answer 2

The Replacement Bar for B&W Biker Bar Motorcycle Tie-Down System #BWMC2302B fits the frame diameter of 1.250" to 1.375" and width 10" to 14.5" softail bikes. The B&W Biker Bar Motorcycle Tie-Down System for Trailers…

view full answer...

Answer 3

I checked with B and W to find out how to tell the two Biker Bars you have apart and they told me that the #BWMC2301 has black pads where it grabs the frame and the part #BWMC2302 has gray pads. While she didn't specify what the overall…

view full answer...

Answer 4

That will depend on which model B&W Biker Bar Motorcycle Tie-Down System you have installed on the trailer. The #BWMC2301 will only work with touring bikes and the 2016 Fat Boy would be considered a softail and needs the #BWMC2302. You can…

view full answer...

Answer 5

I checked with B and W and the Biker Bar part #BWMC2300 would work well on your 2016 Harley CVO Breakout. They state that this fits all Harleys that have painted frames like what your bike has so it would work well.

view full answer...

Answer 6

Great question, Jeff! When the Rota-Flex first came out it renovated what a pin box could do and be, but at this point in time that technology is a little more dated and the Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #325-GH-8040 is the "new…

view full answer...

Answer 7

I have a solution for you, but there is not an adapter that will allow you to mount the B&W Biker Bar #BWMC2301 to an e-track setup on a trailer. The Biker Bar does come with mounting plates/anchors that are mounted on the underside of your…

view full answer...

Answer 8

The Replacement Bar for B&W Biker Bar Motorcycle Tie-Down System #BWMC2302B is the replacement bar that fits H-D Dyna, Softail, and V-Rod bike frames. The #BWMC2301B is the Replacement Clamping Bar for B&W Biker Bar Motorcycle Tie-Down for…

view full answer...

Answer 9

Because the B&W Biker Bar #BWMC2301 is height adjustable, it provides you with the ability to move the bar up or down in 1/4" increments. It looks like the lowest setting is 3-3/4" and the highest setting is 6-1/2" inches-so if…

view full answer...

Answer 10

First of all that's a pretty sweet looking bike! Secondly, while there are no B&W Biker Bar systems specifically designed for your Indian Chieftain, you still might be able to utilize the Tie-Down System #BWMC2301. I've attached a photo…

view full answer...

Answer 11

The B&W Biker Bar Motorcycle Tie-Down System for Trailers - Harley-Davidson #BWMC2301 fits the Street Glide models like your 2022.

view full answer...

Answer 12

The Ventline Exterior Wall Vent for RV Range Hood, #V2018-01 does not have a screen. The vent is 11-1/2" by 5-1/2" with a 10 bolt pattern. Please note the linked product review video. the holes are set in from the edge by about 1/2" to…

view full answer...

B&W Biker Bar for a 2003 Harley Davidson Heritage Springer

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching