Is Fascia Trimming Required to Install Draw-Tite Hitch on 2020 BMW X5

Question

Question:

Plan on getting the drawtite 76288 hitch for my 2020 BMW X5. Wondering if I will need to trim the bumper at all during install. Thanks for any specifics you can provide!

asked by: Frank

0

Expert Reply:

Yes, the Draw-Tite Max-Frame Trailer Hitch Receiver # 76288 for your 2020 BMW X5 will require you to trim a section of bumper fascia to allow clearance for the drop-down receiver. You will just need to use a utility knife to cut out this 3-1/4" x 4" opening (see attached image).

I have included the full instructions manual below that you can also use for reference.

expert reply by: Chris R

0

click to enlarge

Answer 1

Well for starters you'd need to pay the cost of the hitch, but for installation that would depend on the place you go to. If you plan on coming to etrailer and having us install it, you'd need to call our customer service department and…

view full answer...

Answer 2

It's not complicated at all to use your Kuat 4 Bike Rack with your BMW X5, you're just going to need at least a class III hitch like the Curt Trailer Hitch Receiver #C85VV. I'm not going to sit here and tell you that it's an easy job…

view full answer...

Answer 3

Your vehicle is only compatible with the Stealth branded racks. We have two options, the Stealth Hitches Hidden Trailer Hitch Receiver w/ Towing Kit, part #SH25VR and the Stealth Hitches Hidden Rack Receiver, part #SH89VR . The hitch receivers are…

view full answer...

Answer 4

The Stealth Hitches Hidden Trailer Hitch Receiver w/ Towing Kit #SH25VR will not require any additional programming on your 2021 BMW X5. The wiring in this harness is passive so no programming required. You will be able to switch off the parking…

view full answer...

Answer 5

With the Stealth hitches like the #SH25VR that fits your 2022 BMW X5 that comes with the ball mount there aren't any other options for ball mounts that would have different rises or drops. There is only the one setup that can be used and when we…

view full answer...

Answer 6

The Draw-Tite Max-Frame Trailer Hitch Receive part #76288 which is a fit for a 2019 BMW X5 (Non M-Sport) will sit directly below the rear bumper. I don't have any measurements or photos yet as we have not yet had a chance to install this but it…

view full answer...

Answer 7

We have the Draw Tite hitch part #76288 as a confirmed fit that would be a really great choice for your 2014 BMW X5. It's mostly hidden and has really great towing capacities so it's the best hitch for your vehicle.

view full answer...

Answer 8

The only trailer hitch we have listed as a confirmed fit for your 2019 BMW X5 at this time is from Draw-Tite, not Curt. For this, you will want to use the Draw-Tite Max-Frame Trailer Hitch Receiver part #76288. This hitch is a direct fit which means…

view full answer...

Answer 9

That's a good question, and there is no type of fascia or bumper trimming needed in order to install the Stealth Hitches #SH89VR or #SH25VR on your 2021 BMW X5. The bumper and fascia remains intact, though there is a small piece under the vehicle…

view full answer...

Answer 10

The Stealth Hitches that fit your 2022 BMW X5 will have a 600 lb tongue weight rating and an 8,000 lbs tow weight rating. If you are planning on using this for accessories, like a bike rack or cargo carrier, then you need the kit #SH89VR which comes…

view full answer...

Answer 11

Yes, the Draw-Tite Trailer Hitch Receiver #76288 that fits your 2019 BMW X5 does require some trimming of the bumper fascia, though it is not going to be noticeable. As you can see by the cut out of the linked directions, the fascia will need to be…

view full answer...

Answer 12

The Draw-Tite Max-Frame Trailer Hitch Receiver #76288 that is confirmed to fit your 2022 BMW X5 will require you to trim the fascia on your bumper and mounting plate. But these trimmings are not going to be visible with the hitch installed. You will…

view full answer...