Convert-A-Ball AMSC8 Cushioned Ball Mount Length

Question

Question:

I need to know the length of this hitch, thank you

asked by: Wiebe B

0

Expert Reply:

The length of the Convert-A-Ball AMSC8 cushioned ball mount is 11-1/4 inches from the center of the ball mount hole to the center of the hitch pin hole. From the center of the hitch pin hole along the top to the back of the ball mount angle is 5-1/4 inches. From the center of the hitch pin hole along the bottom to the welded gusset is 4 inches. Total over all length end to end is 15 inches.

expert reply by: Robert G

0

Answer 1

For trailer hitch #e98903 and your 2018 Chrysler Pacifica I recommend etrailer ball mount kit #989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch rise or 4 inch drop. It also includes a 1-7/8 inch…

view full answer...

Answer 2

In order to find the correct amount of rise/drop to look for in a ball mount you simply need to measure the distance from the ground to the bottom of the trailer coupler while level and then from the ground to the top inside edge of the receiver on…

view full answer...

Answer 3

We don't have a 5 inch drop ballmount for a 2 inch receiver (only 2-1/2 inch receivers), but a 6 inch ballmount, like #D-28, which you reference, will work just fine. The hitch ball can be an inch or so above the coupler height, since when they…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 10

Yep, so long as your 2024 Subaru Crosstrek Wilderness is not a hybrid both the Curt and etrailer hitches will fit: - Curt Trailer Hitch Receiver #C13382 - etrailer Trailer Hitch Receiver #e98912 The only difference besides price is the finish; the…

view full answer...

Answer 11

Normally trailer coupler height is around 17 inches, from the ground to the bottom of the coupler, and most hitch manufacturers design their hitches to work with a ball mount that will end up very close to this measurement. I am including a link to…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Convert-A-Ball AMSC8 Cushioned Ball Mount Length

Product Page this Question was Asked From

Continue Researching