Center to Center Bolt Hole Distance Where the Tire Mounts on Bumper Mounted Tire Carrier # TR-1

Question

Question:

Hi. What is the distance on center of the bolts that bolt to the actual wheel?

asked by: Bob

0

Expert Reply:

I went out to the warehouse and pulled a bumper mounted tire carrier # TR-1 to measure. The mounting holes where you would mount the tire are 3 inches apart on center. I have included a picture showing this measurement for you.

expert reply by: Michael H

0

click to enlarge

Answer 1

I was able to find some good pictures of your 2023 Dutchmen Coleman Rubicon 1400BH and it looks like you have ST215/75R14 tires on there. Check the sidewall of the tire to verify this is the correct size. This means you have 14" wheels. I can…

view full answer...

Answer 2

Tires like the Castle Rock ST225/75R15 Radial Trailer Tire w/ 15" Silver Mod Wheel - 6 on 5-1/2 - LR D #LHACK124 come with a 5 year warranty on the tires along with 2 years of roadside assistance. Although the roadside assistance would be in…

view full answer...

Answer 3

Thanks for including a picture! To determine if the Bumper Mounted Tire Carrier, #TR-1, will fit a 2002 Coachman Catalina Lite 248TB which angles at the rear, you will want to measure 18-1/4 inches straight up from the bottom front of the bumper.…

view full answer...

Answer 4

Thank you for providing a picture that is similar to what you have! The first thing you will want measure is the diameter of your current tire and wheel combo. The most common tire sizes will have three parts, for example 205/75-R15. This number will…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

I do have an option for you but the only way for you to tow this trailer and have everything work would be to switch from the odd two plug setup to a standard one plug, 7-way trailer connector. This can be done easily with a junction box like the…

view full answer...

Answer 7

The nut on the spindle should be tightened until snug, with no side-to-side play in the hub and then backed off slightly, about maybe a 1/8 of a turn. If the spindle uses a castle nut and cotter pin or tang nut, tighten the nut finger tight until it…

view full answer...

Answer 8

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

Answer 9

In order to replace the Advent Analog Wall Thermostat ACTH11 you'll need the Air Distribution Box w/ Wall-Mounted Thermostat for Advent Air RV Air Conditioners part #ACRG15. This is a digital style replacement which is what you'll need since…

view full answer...

Answer 10

The Tekonsha OEM Vehicle Wiring Harness #22121 that you referenced includes all the wiring and parts necessary to install a fully functional 7-Way connector and trailer brake controller. The included brake controller harness is compatible with and…

view full answer...

Answer 11

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 12

Actually on brake magnets for trailers either wire can be used as the power or the ground so the colors don't really mean anything. Most likely the magnet manufacturer just put what ever color was most convenient on your trailer.

view full answer...

Center to Center Bolt Hole Distance Where the Tire Mounts on Bumper Mounted Tire Carrier # TR-1

Product Page this Question was Asked From

Continue Researching