What Rear Bumper Modifications are Required to Install a Draw-Tite Hitch on a 2012 BMW X5
Question:
i intend to buy hitch for my 2012 X5, wanted to know how to trim back bumper in order to fit hitch? what kind of tool i should use? thank you and have a nice weekend.
asked by: Lixin S
Expert Reply:
You will need to remove a few screws and fasteners to remove a section of the rear fascia to install the Draw-Tite Hitch # 75600, and you will need to trim a section out of the rear fascia.
Check out the pictures that I attached that show the areas where the bolts and fasteners are, I also attached installation instructions for this product for you to check out, the section that needs to be trimmed is outlined in a diagram in these instructions.
Here are the steps for removing the rear section:
1) Remove the first 3 rivets from the rear fender flare, and pop off the flare on both sides. Remove the 8mm bolt hidden under the fender.
2) Remove the rear reflector lights underneath the taillights and remove the 8mm bolt.
3) From underneath remove six 8mm bolts located along the bumper.
4) Open your bottom tailgate at a 45 degree angle and notice the tabs. Pull apart the tabs by squeezing the tab and lift out.
5) From the side of the vehicle, grab the bumper fascia and pull towards you. Do this to both sides. Make sure not to warp the bumper while pulling, distribute force evenly.
6) From the rear of the vehicle pull on the corner adjacent the taillights until you hear it pop free, do not yank on the fascia.
7) From the rear center pull bumper fascia until it slides off.
Product Page this Question was Asked From
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class IV - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class IV
- 600 lbs TW
- 6000 lbs GTW
- 6000 lbs WD GTW
- 2 Inch Hitch
- 600 lbs WD TW
- Concealed Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Trailer Hitch
- Shop: Brake Controller
- Video: Best 2013 Bmw X5 Trailer Hitch Options
- Shop: Trailer Wiring
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class IV - 2"
- Search Results: wireless trailer brake controller
- Q&A: Recommended Hitch, Wiring Harness, and Brake Controller for a 2013 BMW X5 35i
- Q&A: Bracket To Mount 7-Way Plug On Class III Trailer Hitch With Concealed Cross Tube
- Shop: Curt Easy Mount Bracket for 4- or 5-Way Flat and 6- or 7-Way Trailer Connectors - 2" Hitch
- Shop: Redarc Tow-Pro Liberty Brake Controller - Dash Knob - 1 to 2 Axles - Proportional
- Shop: Redarc Tow-Pro Elite Brake Controller - Dash Knob - 2 Braking Modes - 1 to 3 Axles - Proportional
- Shop: Curt Echo Wireless Brake Controller - 7-Way Plug Mount w/ Bluetooth App - 1 to 2 Axle - Proportional
- Search Results: pry tool
- Search Results: no~drill mount for electrical mounting bracket
- Search Results: bracket hanger
- Search Results: 7 pin connector bracket
- Video: Curt Trailer Hitch Installation - 2013 BMW X5
- Video: Trailer Hitch Installation - 2013 BMW X5 - Draw-Tite
- Q&A: Recommended 4-Way Trailer Connector Mount for Hidden Crossbar Trailer Hitch
- Search Results: trailer brake controller
- Search Results: wireless brake controller
- Shop: Curt Shock Absorbing Towing Kit w Sway Control, Wireless Brake Controller - 2-5/16" Ball - 7.5K
- Q&A: Brake Controller Recommendation for 2015 BMW X5
- Q&A: Parts Needed to Add Trailer Hitch, Wiring Harness and Brake Controller to 2011 BMW X5
- Q&A: Trailer Hitch Options for a 2011 BMW X5
- Q&A: Removing Rear Bumper Fascia from a 2012 BMW X5 For Draw-Tite Trailer Hitch Installation
- Video: Draw-Tite Hitch Anti-Rattle - Standard Anti-Rattle - 63080 Review
- Video: Stealth Hitches Hidden Trailer Hitch Installation - 2022 BMW X5
- Video: Choosing the Right Trailer Wiring