Brake Controller 7 & 4 Way Installation Kit Fuse Slot Number 5 2009 Honda Odyssey

Question

Question:

2009 Honda Odyssey wiring harness with brake. What size fuse goes into slot number 5 on the passenger side?

asked by: Rusty

0

Expert Reply:

It is a 7.5 amp fuse which goes into the fuse box in the side kick panel. I will include a link to the web page with the instructions, and the installation video for your reference below.

expert reply by: Renee B

0

Answer 1

The model of vehicle does impact the time it takes to install a trailer hitch and wiring, although for a 2017 Ford Transit T250 a decent ballpark estimate is 1-1/2 to 2 hours. The good news is there is a very simple to install trailer hitch for a…

view full answer...

Answer 2

Not to confusing at all. There are a lot of wires to keep straight, but once you do it, you will be surprised at how easy it was. I will go through a quick run down of how to wire up the ETBC7, then how to wire up the Brake Controller. I will also…

view full answer...

Answer 3

Your Explorer will not have the brake controller wiring unless it has the 7 way connector on the bumper. Since you have the 4 way, you would need to use the Brake controller installation kit, part #ETBC7. The kit would actually contain the 4 to 7 way…

view full answer...

Answer 4

On your 2016 Ford Transit T350 it sounds like you have the hardwired 7-way and a damaged brake controller. My recommendation is to replace your wiring with the Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector #C56327 and…

view full answer...

Answer 5

I would be happy to help! Starting with the trailer hitch receiver I recommend the etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2" #e98842 which is confirmed to fit your customer's 2019 Ford Transit T250…

view full answer...

Answer 6

You will need to install a Brake Controller in your RV to actuate the brakes on your trailer. In addition to the Controller, you will also need the 7-Way Installation Kit #ETBC7. The existing 4-Way connector on your RV would plug into the 7-Way…

view full answer...

Answer 7

If your trailer is equipped with a 7-Way but you only need to power its basic signal lights (and not electric brakes) then adding a 7-Way connector to your 2020 Ford Transit T250 will actually be fairly simple. To do this you will need to start with…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 11

The best brake controller option to go with is one that activates the brakes proportionally instead of time delayed. A proportional brake controller will activate the trailer brakes at the same time and with the same intensity as the tow vehicle…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Brake Controller 7 & 4 Way Installation Kit Fuse Slot Number 5 2009 Honda Odyssey

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching