Brake Controller Installation on a 2008 Ford Explorer with 4-Pole Trailer Connector
Question:
I have a 2008 Ford Explorer and need a 7 pin connector and brake controller. Does a new brake controller simply plug in somewhere on the explorer? Is there an adapter to convert the 4 pin connector to the 7 pin and does this eliminate the need to run wiring from the front to the rear of the vehicle?
asked by: Bob
Expert Reply:
Your Explorer will not have the brake controller wiring unless it has the 7 way connector on the bumper. Since you have the 4 way, you would need to use the Brake controller installation kit, part # ETBC7. The kit would actually contain the 4 to 7 way adapter, as well as all the wiring needed to complete the installation. We also have an online video and FAQ article that will help explain how to use the install kit, as well as an installation video showing a brake controller being installed on a 1996 Explorer. The install procedure for your 2008 Explorer will be similar to that shown in the video.
I will provide links to the videos, as well as links to other information that will assist you with the install.
Products Referenced in This Question
Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Accessories and Parts
- Trailer Brake Controller
- Installation Kits
- etrailer
more information >
Product Page this Question was Asked From
Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Accessories and Parts
- Trailer Brake Controller
- Installation Kits
- etrailer
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Brake Controller
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Video: Curt Echo Mobile Trailer Brake Controller Installation - 2019 Ford Explorer
- Shop: Trailer Wiring
- Q&A: Location of Factory Brake Controller Plug on a 2008 Ford Explorer
- Shop: Curt Echo Wireless Brake Controller - 7-Way Plug Mount w/ Bluetooth App - 1 to 2 Axle - Proportional
- Video: Coil SumoSprings Rear Axle Helper Springs Review
- Video: Review of Tow Ready No Drill Mount Bracket - 18136
- Video: Review of etrailer - Brake Controller - ETBC7
- Video: 3M Wiring 44-5310A Review
- Shop: Suspension Enhancement
- Search Results: dw05745
- Search Results: 44~5310a
- Shop: EZ Connector Magnetic 7-Way Trailer Connectors w/ Watertight Seal - Custom - Vehicle/Trailer End
- Shop: Towing Mirrors
- Shop: Hayes Syncronizer Trailer Brake Controller - 1 to 2 Axles - Time Delayed
- Shop: Ring Terminal - 12-10 Gauge Wire - 3/16" Ring ID
- Shop: Extension Cable for Hopkins Smart Hitch Backup Camera - 5 ft
- Shop: Deka Butt Connector - 12-10 Gauge - Nylon Insulation - Yellow - Qty 1
- Search Results: adapter
- Search Results: backup camera
- Search Results: hm50002
- Search Results: no drill mount bracket
- Search Results: bracket for 7 way
- Q&A: Replacement 7-Way and Mounting Bracket for Damaged Parts of ETBC7 Kit
- Q&A: Can Hopkins Smart Hitch Backup Camera be Plugged Into 7-Way From ETBC7 Kit
- Q&A: How to Determine Towing Capacity for 2010 Toyota Highlander, Hitch and Camera Recommendation
- Q&A: Wire Gauges for Hopkins Endurance Trailer Connector with Universal Pigtail Harness # 47210
- Q&A: Finding Stoplight Circuit for Brake Controller Install Ford Dump Truck
- Q&A: How to Use Circuit Tester of ETBC7 Universal Installation Kit for Trailer Brake Controller