Taillights to Replace Existing Wesbar 50010 on Ez Loader Trailer

Question

Question:

Hello. Do you have a replacement lens for a Westbar 50011 light? The 3335 looks close.

asked by: STEVE

0

Expert Reply:

According to Wesbar, that lamp was discontinued around 2000 or so. Unfortunately, you'll need to replace the lamps but the good news is that Optronics makes a direct replacement LED lamp not terribly expensive. I'd recommend going with # STL008RB for the passenger side and # STL009RB for the driver's side.
The LED lamps are fully sealed, so they'll be great for marine use. LED's draw a fraction of the power that incandescent bulbs do, and they are brighter and last MUCH longer.

expert reply by: Mike L

0

Answer 1

Thanks for the pictures and the dimensions! The best option we have for you is the Optronics LED Combination Trailer Tail Lights #TLL160RK which measure 8-1/16" long x 2-7/8" tall x 2-13/16" deep, and have a three mounting slots…

view full answer...

Answer 2

Yes, the CE Smith Trailer Hub part #CE13511 will fit as a replacement for your DICO hub 45264 but you will need to use a different seal as we have found that your spindle diameter is slightly different which means you need the #168255TB as well.

view full answer...

Answer 3

Dico was bought out by Titan who now offers 5-on 4-1/2 idler hub #DX22XR. This hub is rated for 2500-lb axles and includes bearings, races, grease seal, grease cap, and lug nuts. You can be assured it will fit the trailer spindle as long as the…

view full answer...

Answer 4

I contacted ShoreLand'r Trailer for the original wheel and tire size supplied on your trailer model B16750-12. My contact there was able to find some data on this 1988 trailer. He indicated that the original tire size was either a 4.80-8 or a…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 8

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 11

The UFP H-1377 correlates to a Dexter #84 spindle, which is for a 3,500 pound axle. This will utilize an inner bearing #L68149 and an outer bearing #L44649. As this is being used on a boat trailer, I highly suggest going with the etrailer.com…

view full answer...

Answer 12

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...