Will Bumper Fascia Need Trimming to Install EcoHitch 306-X7332 on 2020 Volkswagen Golf R

Question

Question:

To install the EcoHitch 306-X7332 on my 2020 Volkswagen Golf R, will I need to cut the bumper cover?

asked by: Tim P

0

Expert Reply:

Per the instructions included with the EcoHitch # 306-X7332, the bumper fascia will need to be notched, a 3 x 3-1/4 inch section would need to be removed, as seen in the photo I've provided.

expert reply by: Mike L

0

click to enlarge

Answer 1

Yes, all of the trailer hitches for your 2019 Volkswagen Golf R require some fascia trimming for the installation. Out of the available options I recommend going with the EcoHitch #306-X7332 because it is he only option for you to use a 2"…

view full answer...

Answer 2

I don't see any mention of sensors on any of the instructions for the EcoHitch Hidden Trailer Hitch Receiver part #306-X7332. Is it possible they can be added on to the 1/2" hardware installed further toward the middle now like in the…

view full answer...

Answer 3

The hitches that fit your 2019 Volkswagen Golf R like the EcoHitch #306-X7332 all require some fascia trimming. This EcoHitch is the way to go though as it's only option that has a 2 inch opening which more accessories are made for and is in…

view full answer...

Answer 4

To install the EcoHitch #306-X7333 or #306-X7332 on a 2019 VW Golf R, a notch measuring 3 x 3-1/4 inches would need to be made in the underside of the bumper fascia. For both hitches, the notch isn't noticeable from the rear, only if you're…

view full answer...

Answer 5

For your 2019 Volkswagen Golf R we have 2 hitches from EcoHitch and one from Stealth. The cutout of the Stealth #SH89ZR is minimal while for the EcoHitch #306-X7333 is 3-1/4" x 3" and #306-X7332 it is 4-1/4" x 3". I would…

view full answer...

Answer 6

As you mentioned, the EcoHitch #306-X7332 requires you to trim the fascia for installation.The cutout required to install the EcoHitch is 3-1/4” wide x 3” tall. There is also a 2" EcoHitch #306-X7333 available for the 2019 VW Golf R that…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 10

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 11

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Answer 12

Normal operating temperatures for drum brakes range from 150-400 degrees F. During certain stopping conditions the brake heat can exceed 600 degrees. The effectiveness and stopping power of the brakes is significantly reduced at these higher…

view full answer...

Will Bumper Fascia Need Trimming to Install EcoHitch 306-X7332 on 2020 Volkswagen Golf R

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching