Replacement Rear Latch Clamp for Extang Solid Fold

Question

Question:

Where can I get the hold down latch for Extang solid fold?

asked by: Louis S

0

Expert Reply:

Thanks for the picture of the latch you are needing. Based on that you are in need of the part # EX1035 which is a replacement tail clamp assembly for the Solid Fold.

expert reply by: Jameson C

0

click to enlarge

Answer 1

In order to install the Replacement Tail Clamp Assembly for Extang Solid Fold and Trifecta Tonneau Covers part #EX1035 you'll simply remove the hinge cap, slide the old clamp off, slide the new clamp on, then reinstalled the hinge cap. I have…

view full answer...

Answer 2

The Replacement Jaw Grip Clamp for Extang Solid Fold 2.0 Tonneau Covers #EX1035 and front clamp #EX42FJ have a very basic design of a bolt with a nut on the end. You will remove the hinge cap or latch pocket cover from the cover and simply slide out…

view full answer...

Answer 3

To install the Extang Replacement Tail Clamp Assembly #EX1035 into an Extang Solid Fold you will need to cut a notch in the channel. A spot near the middle of the cover is preferred. Usually you'll only need to make a notch on one side of the…

view full answer...

Answer 4

To install the Extang Replacement Tail Clamp Assembly #EX1035 into an Extang Solid Fold 2.0 Hard Tonneau Cover like #EX83651 you will need to cut a notch in the channel. A spot near the middle of the cover is preferred. Usually you'll only need…

view full answer...

Answer 5

To replace the clamp on your Extang Solid Fold 2.0 you need to remove the clamp cover (there is a screw that needs to be removed first) and then you can remove the clamp for replacement. If you have a different Extang 2.0 tonneau cover please let me…

view full answer...

Answer 6

I can help you with the process of replacing the Tail Clamp Assembly #EX1035 for your Extang Solid Fold or Solid Fold 2.0 tonneau cover. The replacement process will be different depending on if your existing cover is the Solid Fold or the Solid Fold…

view full answer...

Answer 7

The Replacement Tail Clamp Assembly for Extang Solid Fold and Trifecta Tonneau Covers #EX1035 does work on both the driver and passenger side of the truck. I can also confirm this is the correct replacement clamp for the Extang Trifecta 44630 tonneau…

view full answer...

Answer 8

Try using a couple wrenches to loosen the nut and bolt on the top and bottom of the Replacement Tail Clamp Assembly #EX1035 that you referenced. This will allow the spring inside of it to not need to compress as hard when releasing it.

view full answer...

Answer 9

I spoke with my contact at Extang about the install of the front clamp for Trifecta Cover Clamp part #EX1034 that you referenced and he said that you need to disconnect the screws from the crossbow of the cover so that it will drop down and the cab…

view full answer...

Answer 10

A lid or cover does not need to be removed in order to install the Replacement Tail Clamp Assembly for Extang Solid Fold and Trifecta Tonneau Covers #EX1035. For the SolidFold 2.0 you will undo the screws from the crossbow of the cover which should…

view full answer...

Answer 11

The correct replacement cab clamp for the Extang Solid Fold 2.0 that you need is part #EX42FJ.

view full answer...

Answer 12

None of the methods are super easy. I'd recommend three though you have to remove hinges. This is least invasive, doesn't require cutting the cover, and also doesn't risk damaging cover.

view full answer...

Replacement Rear Latch Clamp for Extang Solid Fold

Product Page this Question was Asked From

Continue Researching