Does Cover Need to be Removed to Install Replacement Tail Clamp Assembly for Extang Solid Fold

Question

Question:

I found a replacement clamp but where do I find this “lid or cover” that needs to be removed to install this new clamp or latch. I don’t know the exact name for this item, sorry.

asked by: John N

0

Expert Reply:

A lid or cover does not need to be removed in order to install the Replacement Tail Clamp Assembly for Extang Solid Fold and Trifecta Tonneau Covers # EX1035.

For the SolidFold 2.0 you will undo the screws from the crossbow of the cover which should allow you to slide the new clamp on.

expert reply by: Kyle S

0

click to enlarge

Answer 1

Yes, the part #EX1035 is the correct replacement tail clamp assembly for an Extang Solid Fold tonneau cover like what you have. I attached install instructions for this clamp for you to check out as well.

view full answer...

Answer 2

In order to install the Replacement Tail Clamp Assembly #EX1035 on your Extang Trifecta Tonneau Cover, you will need to cut a notch in the channel, somewhere near the middle of the cover. You should only need to make a notch on one side of the…

view full answer...

Answer 3

Thanks for the picture of the latch you are needing. Based on that you are in need of the part #EX1035 which is a replacement tail clamp assembly for the Solid Fold.

view full answer...

Answer 4

To install the Extang Replacement Tail Clamp Assembly #EX1035 into an Extang Solid Fold you will need to cut a notch in the channel. A spot near the middle of the cover is preferred. Usually you'll only need to make a notch on one side of the…

view full answer...

Answer 5

To install the Extang Replacement Tail Clamp Assembly #EX1035 into an Extang Solid Fold 2.0 Hard Tonneau Cover like #EX83651 you will need to cut a notch in the channel. A spot near the middle of the cover is preferred. Usually you'll only need…

view full answer...

Answer 6

I can help you with the process of replacing the Tail Clamp Assembly #EX1035 for your Extang Solid Fold or Solid Fold 2.0 tonneau cover. The replacement process will be different depending on if your existing cover is the Solid Fold or the Solid Fold…

view full answer...

Answer 7

I was not able to find the installation instructions for the Replacement Tail Clamp Assembly, part #EX1035, but I did find the instructions for the Extang Solid Fold Tonneau Cover part #EX83700. I have attached those instructions and you can see…

view full answer...

Answer 8

Thanks for your picture from that it looks like you have an Extang Trifecta tonneau cover and are needing a replacement cab clamp assembly part #EX1034. This is the only way to order and replace the part you are needing to replace.

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Does Cover Need to be Removed to Install Replacement Tail Clamp Assembly for Extang Solid Fold

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching