Installation of a 7-Way Connector on a 1993 Nissan Pathfinder With a 4-Way Connector
Question:
how does system convert to 7 pole flat wire harness to fit trailer I just purchased?
asked by: Mitch
Expert Reply:
The Curt T-Connector Vehicle Wiring Harness, part # C55353, you have referenced, for your 1993 Nissan Pathfinder will give you a 4-Way connector on the rear of your vehicle.
If you are wanting a 7-Way connector on your Pathfinder you will need to add the Hopkins Adapter 4-Way to 7-Way and 4-Way, part # 37185, to the # PTW2993 wiring harness. This Hopkins adapter will plug into your 4-way connector and mount on the rear of your vehicle. The four remaining wires will need to be hardwired to the corresponding circuits on the vehicle.
The white (ground) wire will need to be attached to the vehicle frame, the black (12 volt power) wire is connected to the vehicles battery with 10 gauge wire like the # 10-1-1, through a 40-amp circuit breaker # 9510, the blue (trailer brake) wire will be connected to the blue trailer brake feed wire on the brake controller, and the purple ( auxiliary) wire is for reverse lights if you need that circuit. If any of these connections are not needed just wire tie them up out of the way for future use.
If you are adding a brake controller to your vehicle you can use the Brake Controller 7 and 4 Way Installation Kit, part # ETBC7. This kit will include the # 37185 part mentioned above and the extra wiring and circuit breakers that would be needed for a brake controller. I am including a link to the installation instructions and an installation video on the # ETBC7 kit.
Products Referenced in This Question
Adapter 4-Pole to 7-Pole and 4-Pole
- Trailer Wiring
- Wiring Adapters
- Multi-Function Adapter
- 4 Flat
- Plug and Lead
- 4 Flat
- 7 Round - Blade
- Hopkins
more information >
40 Amp In-Line Circuit Breaker - Perpendicular Mount Bracket
- Accessories and Parts
- Wiring
- Circuit Breaker
- 40 Amp
- Pollak
more information >
Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Accessories and Parts
- Trailer Brake Controller
- Installation Kits
- etrailer
more information >
Product Page this Question was Asked From
Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Converter
- Custom Fit
- 4 Flat
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: Converting From 7-Way Round to 7-Way Flat Connector
- Q&A: Proper Position of Equalizer and Shackles on Trailer Suspension
- Article: Double-Eye Trailer Suspension System Review
- Article: Slipper Spring Trailer Suspension System Review
- Q&A: 7-Way Round Commercial Vehicle End Connector To 7-Way Blade Trailer Connection
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Q&A: Replacement Hub Assembly for T.D.E. 11033
- Q&A: Trailer Wiring Harness for 1995 Nissan Pathfinder
- Q&A: Will Curt Trailer Hitch Receiver # C13095 Opening Sit Flush with Bumper on 1991 Nissan Pathfinder
- Article: Routing the Power Wire for a Trailer Wiring Harness
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Trailer Hitch Installation Tips
- Q&A: Recommended Trailer Hitch Receiver and Wiring for 1996 Nissan Pickup
- Article: Performance Chips and Modules