Hydraulic Line Size Used with Demco Reverse Lockout Solenoid DM5837

Question

Question:

Wats the line measurement 3/8 or 5 /16

asked by: Guillermo T

1

Helpful Expert Reply:

The Reverse Lockout Solenoid in the Demco kit # DM5837 installs in line with your master cylinder and a standard 3/8" hydraulic line, like # bh-3mfs-24.

The # DM5837 is designed to work with Demco models DA10 and DA91 hydraulic trailer brake actuators.

expert reply by: Carla M

1

Answer 1

Hello Bob, For your Demco DA70 actuator use the Reverse Lockout Solenoid #DM11993. The difference between this and #DM5837 is that the latter comes with a cover.

view full answer...

Answer 2

Atwood is out of business which is why there isn't a replacement master cylinder to be found. So you'll have to replace your actuator with an appropriate option, like the Demco Hydraulic Brake Actuator - Disc #DM62VR or Drum #DM72VR…

view full answer...

Answer 3

We do indeed have some LED taillights that'd work great on your boat trailer. I'd recommend #STL57RB for the driver side and #STL56RB for the passenger side. These lamps measure 6-1/16 x 2-5/8 inches, and would work well on your…

view full answer...

Answer 4

I have attached a chart you can check out that describes the torque needed per wheel size, wheel stud size and material. For an 8-inch wheel with a 1/2-inch wheel stud the torque is 75 to 86 ft-lbs. For a 15 inch steel wheel with 1/2 inch wheel studs…

view full answer...

Answer 5

90-120 ft lbs of torque is probably about right for your 15 inch trailer rims. If you check out the lug nut torque chart that I attached you will see that nearly all of the torque specs are that and higher. You'll need to know the diameter of the…

view full answer...

Answer 6

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 7

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 8

The AL-KO trailer hub part number 8700 that you have is a 3,500 lb trailer hub/drum with a 5 on 4-1/2 inch bolt pattern. Based on that the #AKHD-545-35-EZ-K is the correct fit and would work great.

view full answer...

Answer 9

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 10

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 11

The amount of bow that's put into trailer axles like the #7359765 is based on about how much a trailer is typically going to weigh that has a 3,500 lb capacity. So there's a bit of approximation and obviously it can't be totally perfect…

view full answer...

Answer 12

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Hydraulic Line Size Used with Demco Reverse Lockout Solenoid DM5837

Product Page this Question was Asked From

Continue Researching