Upgrading 4-Way of 2014 Nissan Xterra to 7-Way Parts Needed

Question

Question:

I installed sometime ago the four-way hitch connector along with the relay kit together and everything’s fine I wanted to replace the four-way with your seven way Connector wanted to make sure I was looking at the right product I have a 2014 Nissan Xterra six cylinder four-wheel-drive

asked by: John A

0

Expert Reply:

Since you already have all of the relays from the 4-way install all you need to convert it to a 7-way is the part # 118282. This comes with the needed harnesses and the 7-way plug so it would be all you'd need.

expert reply by: Jameson C

0

Answer 1

Since you already have all of the needed relays from the #C56225 to upgrade to a 7-way all you need is the #118282 and you'd be set!

view full answer...

Answer 2

The correct 7-way trailer wiring harness for your 2005 Nissan Pathinder that has the factory 4-way is the kit part #118282. This plugs right in and does not require any wiring or splicing. Since your trailer has brakes you'll need a brake…

view full answer...

Answer 3

Yes, per the installation instructions, your 2014 Nissan Pathfinder with the Controller Area Network, or CAN Bus system, it is recommended by the manufacturer that you use the 30-amp circuit breaker kit #331-CBK30-EB. This, along with your Redarc…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 7

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

If you have a vehicle specific wiring harness for a brake controller then that would indicate that you have a factory tow package and subsequently would already have a 7-way at the back of your vehicle. The universal 7-way connector #ETBC7 is meant…

view full answer...

Answer 12

It could be a tow package fuse on the vehicle. Use the owners manual to find the locations of fuses/relays related to the tow package wiring to check them and replace as needed. If the issue is not a fuse or relay then you can test the vehicle side…

view full answer...