How Far Does The Curt Trailer Hitch Receiver 13412 Stick Out On The 1985 Jeep CJ-7

Question

Question:

85 Cj 7 Laredo. Im looking for a frame mounted hitch, but how far does it stick out past the rear of the Jeep? Im also looking for a bumper and need some sort of reference.

asked by: Mark

0

Expert Reply:

The Curt Trailer hitch receiver part # 13412 sticks out about 6-1/2" from the cross member. You can use the hitch with an aftermarket bumper but all of the bumpers we carry already have hitch receivers integrated into them. When using an aftermarket bumper you would need to use the 7/16 x 2" bolt provided.

expert reply by: Heather A

0

click to enlarge

Answer 1

Yes, the Curt Trailer Hitch Receiver #13412 will indeed work with the stock rear bumperettes on your 1984 Jeep CJ-7.

view full answer...

Answer 2

I spoke with my contact at Curt, who tells me that you can simply disconnect the existing exhaust hanger, install the hitch, and then use the bolt shown in the diagram I have provided to reinstall the bracket. The bolt would pass through the…

view full answer...

Answer 3

In order to determine if the Curt Trailer Hitch Receiver part #13412 will fit your 1985 Jeep CJ8 Scrambler you will need to measure the distance between the mounting holes in the rear crossmember. Unfortunately, the Curt Trailer Hitch Receiver has…

view full answer...

Answer 4

If you are looking for a trailer hitch receiver and wiring for your 1982 Jeep CJ-7 Renegade then you have come to the right place. The Curt Class III Trailer Hitch Receiver #13412 is a great option for a trailer hitch receiver that we have. It has a…

view full answer...

Answer 5

I do have a few hitches that will fit these vehicles individually, however, there are no hitches which will fit on both your 2004 Jeep Wrangler and 1985 Jeep CJ-7. For your 2004 Jeep Wrangler, I recommend the Curt Trailer Hitch Class III #13408. This…

view full answer...

Answer 6

The 6' length of the BoatBuckle Personal Watercraft Cam Buckle Tri-Down Strap #IMF10972BK is of the strap itself from one end hook to the other end hook. We do have this slightly longer in 8' with part #IMF14218. We do have the etrailercom…

view full answer...

Answer 7

We have had this question come up before and have determined after talking to Curt, the manufacturer, that trailer hitch #13412 will fit a 1982 Jeep CJ-7 with the optional 20 gallon gas tank. I am including a link to the installation instructions for…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 11

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

Answer 12

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

How Far Does The Curt Trailer Hitch Receiver 13412 Stick Out On The 1985 Jeep CJ-7

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching