Can I Use 2.5 x 2.5 Gear Pack To Replace Gear Pack On 2 x 2 Slide Out System

Question

Question:

Does the 2x2 come in a heavy duty with steel rollers? If not, can I just order the 2.5x2.5 heavy duty pack and use them on my 2x2 setup?

asked by: Robert

0

Expert Reply:

I understand wanting to use the steel rollers but you want to stick with the same size Gear pack roll pins for the 2 x 2 slide arm setup part # LC281331. The 2.5 x 2.5 gear pack part # LC123356 will not be compatible.

expert reply by: Heather A

0

Answer 1

When RV slide outs start grinding the issue is sometimes something dragging on something else in the track. It can be that the tracks had something fall into them and now that is what you are hearing or they are misaligned. Sometimes it can also be…

view full answer...

Answer 2

I called and spoke to the technician at Lippert about the gear packs. If the arms that attach to your slide out are 2 x 2 you will need Gear Pack part #LC281331. If the arms that attach to the slide out at 2.5 x 2.5 you can certainly use Gear Pack…

view full answer...

Answer 3

The Lippert 2 X 2 Slide-Out Gear Pack Without Roll Pins Assembly #LC281331 has the following dimensions pictured below and the gear has 15 teeth.

view full answer...

Answer 4

Since your slide out was manufactured before October of 2013, you&#39;ll need the 18 tooth gear #LC122739 along with the Lippert 2 X 2 Slide-Out Gear Pack Without Roll Pins Assembly #LC281331. The gear included with the Lippert 2 X 2…

view full answer...

Answer 5

Manufacturers do not list the parts they use so we do not know what size gear pack is needed for your 2010 Tiffin Allegro Open Road 34TGA without first measuring the arm. For a 2 x 2 Arm you'll need part #LC281331. For a 2.5 x 2.5 Arm…

view full answer...

Answer 6

The gear included with 2x2 gear pack #LC281331 is a 15 tooth gear.

view full answer...

Answer 7

Most likely the gear pack on the right side is worn and skipped a bit throwing off the alignment of your slide out. You should first start by checking for any kind of obstructions that could prevent the slide out from fully retracting and then…

view full answer...

Answer 8

You'll need to measure the arm (pictured below) to determine the correct size gear pack replacement for your trailer's slide outs. For 2" x 2" you'll need #LC281331 For 2.5" x 2.5"…

view full answer...

Answer 9

That looks like a Lippert slide out based on your pictures like the part #LC281331 which has a 15 tooth gear on it. If the tubing the gear rides on is 2 inch by 2 inch like it looks like this would be correct.

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better…

view full answer...

Answer 12

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors…

view full answer...