Replacement 1/2" Diameter x 1-1/2" Long Wheel Studs Needed for 2011 Eclipse 26BH Travel Trailer

Question

Question:

hi i have a 2011 eclip travel trailer 26bh broke the studs on wheel cant find at parts store need help, 1-1/2 long have standard treads 1/2 in diameter

asked by: Jimmy A

0

Expert Reply:

We do have the Replacement Trailer Hub Wheel Stud # 165981 which is 1-1/2" long with a 1/2" diameter. This is a drive-in stud which is pretty typical on trailers. If you need more than 1 we have the 4-pack as part # RG03-020.

I am attaching a photo of the dimensions for this stud so you can compare with what you have. If something is a little different please let me know and I can help you choose the correct replacement for your application.

expert reply by: Jon G

0

click to enlarge

Answer 1

The exact replacement hub assemblies you need are the AxleTek Trailer Hub and Drum Assembly - 3,500-lb Axles - 10" Diameter - 5 on 4-1/2 #AKHD-545-35-K. These assemblies come with the bearings, races, seal, grease cap and even the lug nuts…

view full answer...

Answer 2

Most wheel studs are pressed into hubs so what you can do is use a large punch or chisel and a hammer to hammer the broken studs out of the hub and then reverse the process to install new ones.

view full answer...

Answer 3

The seal you need for your trailer hub is the #58846. Or for a bearing kit that includes all of the components you'll need you'd want the #BK2-100. For brake assemblies you'd want the part #AKEBRK-35L for the left side or part #AKEBRK-35R…

view full answer...

Answer 4

The exact replacement hub assemblies you need for your BD2-545-17 are the etrailer Trailer Hub and Drum Assembly - 3,500-lb Axles - 10" Diameter - 5 on 4-1/2 #AKHD-545-35-K that you referenced.

view full answer...

Answer 5

I couldn't be 100% positive about which wheel studs you'd need without seeing the trailer and being able to measure. I just don't have enough information. This bein said, by virtue of the trailer having a 5 on 4-1/2 inch wheel bolt…

view full answer...

Answer 6

I took a look at the wheel lug stud LCI SKU 121803 you mentioned, and I was able to find the Kodiak Wheel Bolt #K12WB2. This bolt is 2" long, and has a thread size of 1/2"-20 UNF-2A.

view full answer...

Answer 7

The standard replacement drive-in wheel stud for a 3,500 lb hub/drum like what you have on your Lippert 3,500 axle is the part #7-122 which is the correct thread size and length.

view full answer...

Answer 8

We do offer a range of replacement wheel studs, both screw-in and drive-in types, and the link provided will allow you to view these and filter them based on the characteristics you require. The part you referenced, Redline #RG03-020, is close to you…

view full answer...

Answer 9

The hole size that the Replacement Trailer Hub Wheel Stud, Drive-In, part #RG03-020, will use is a 1/2 inch hole. The spline diameter on the wheel stud is 0.62 inches which is a little larger and that allows the wheel stud to have a press fit when…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 12

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Replacement 1/2" Diameter x 1-1/2" Long Wheel Studs Needed for 2011 Eclipse 26BH Travel Trailer

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching