B&W Biker Bar For Harley Davidson 2018 Road Glide

Question

Question:

Which biker bar for 2018 Road Glide on open trailer?

asked by: Pam

0

Expert Reply:

I have contacted B&W and the biker bar compatible with the 2018 Harley-Davidson Touring bikes like the 2018 Road Glide is part # BWMC2301. The B&W Biker Bars can be mounted to an open or enclosed trailer floor with the included hardware.

expert reply by: Heather A

0

Answer 1

If you have a Harley Davidson Road Glide then I can confirm the B&W Biker Bar Motorcycle Tie-Down System for Trailers part #BWMC2301 will work which also fits the Harley Davidson Ultra Classic.

view full answer...

Answer 2

Straps really aren't needed when using the B&W Biker Bar Motorcycle Tie-Down System #BWMC2301. Since it does such a great job securing the bike by the frame chocks and straps just aren't needed.

view full answer...

Answer 3

Most likely your suspension is fine if it was slightly compressed and the wheel turned. In an extreme situation it might twist the forks of the bike in the steering stem a bit which would cause the handle bars to almost feel like they are bent plus…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 7

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 8

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 11

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 12

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

B&W Biker Bar For Harley Davidson 2018 Road Glide

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching