Are Straps Needed When Securing Bike with B&W Biker Bar Motorcycle Tie-Down System # BWMC2301

Question

Question:

Would straps secure the hike even more or would it be unnecessary?

asked by: Matt B

0

Expert Reply:

Straps really aren't needed when using the B&W Biker Bar Motorcycle Tie-Down System # BWMC2301. Since it does such a great job securing the bike by the frame chocks and straps just aren't needed.

expert reply by: Jameson C

0

click to enlarge

Answer 1

Most likely your suspension is fine if it was slightly compressed and the wheel turned. In an extreme situation it might twist the forks of the bike in the steering stem a bit which would cause the handle bars to almost feel like they are bent plus…

view full answer...

Answer 2

I have contacted B&W and the biker bar compatible with the 2018 Harley-Davidson Touring bikes like the 2018 Road Glide is part #BWMC2301. The B&W Biker Bars can be mounted to an open or enclosed trailer floor with the included…

view full answer...

Answer 3

You will need to pull down on the release handles of the B&W Biker Bar Motorcycle Tie-Down System #BWMC2304 which will allow the bike to be released from the mount and then you will be able to push the bike forward. See attached picture to…

view full answer...

Answer 4

I have a solution for you, but there is not an adapter that will allow you to mount the B&W Biker Bar #BWMC2301 to an e-track setup on a trailer. The Biker Bar does come with mounting plates/anchors that are mounted on the underside of your…

view full answer...

Answer 5

When it comes to mounting the B&W Biker Bar Motorcycle Tie-Down System for Trailers - Harley-Davidson Touring #BWMC2301, it isn't the base plate that your aluminum needs to handle but the weight of the bike, as you can see by the cut…

view full answer...

Answer 6

The 3/4" plywood floor will be thick enough to install the B&W Biker Bar Motorcycle Tie-Down System #BWMC2301 and use with your Harley Touring. If you take a look at the accompanying cutout of the directions I added, it states…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 10

I am sorry but we do not have an AC cover with those dimensions. The closest option we have is the Replacement RV Air Conditioner Cover for Penguin and Dometic Air Conditioners item #AT3308046006 which measures 40-1/2" long x 29"…

view full answer...

Answer 11

The P3 brake controller, #90195, will go into a sort of sleep mode after it detects no movement for 15 minutes. While it is on it does not draw very much power. What you can do to make sure it goes to sleep is exit the truck after turning it off,…

view full answer...

Answer 12

Hey Antoine, so the two kits you mentioned are actually really similar and honestly I would go with the part #ETBC7 if I were you. The #ETBC7L is basically the same thing minus a couple wires and breakers so you may as well get the kit that has…

view full answer...

Are Straps Needed When Securing Bike with B&W Biker Bar Motorcycle Tie-Down System # BWMC2301

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching