What are the Mounting Hole Dimensions for the Bulldog A-Frame Trailer Jack # BD155032

Question

Question:

I need the bolt Pattern for the jack. Thanks

asked by: Ken

0

Expert Reply:

I went out to the warehouse and measured a Bulldog A-frame trailer jack, # BD155032. The bolt holes are 3 inches apart on center. I measured a few other A-frame jacks that were nearby and they also had holes that were 3 inches apart on center.

expert reply by: Michael H

0

click to enlarge

Answer 1

The Curt MV Weight Distribution System part #C17050 does not have sway control so reversing is not as big of an issue although the trailer still needs to remain relative straight. If you need to turn and backup it is recommend to unhook the spring…

view full answer...

Answer 2

All A-Frame mounted jacks we offer like the Bulldog Round A-Frame Jack, part #BD155033, use the same 3-inch mounting hole bolt pattern. Are the mounting holes on your trailer slotted at all? If so, a standard 3 inch pattern may still work if you…

view full answer...

Answer 3

Almost all A-frame jacks now have the triangle or round mounting plate with the 3 bolt-3 inch on center holes. We do not carry anything that has the 4 holes. We do have some electric jacks like the Stromberg Carlson Electric Trailer Jack - Drop Leg -…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 6

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 7

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 8

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 9

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 10

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 11

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 12

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

What are the Mounting Hole Dimensions for the Bulldog A-Frame Trailer Jack # BD155032

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching