Replacement Element for Atwood GC6AA-9E Water Heater

Question

Question:

is cam 2103 replacement element for Atwood GC6AA-9E

asked by: Clifford S

0

Expert Reply:

Yes, the Camco Water Heater Element # CAM02103 you referenced will work perfectly as a replacement on your Atwood model GC6AA-9E model water heater. I have attached a sample install video that you might find helpful as well.

expert reply by: Chris R

0

Answer 1

Our search feature can be frustrating but I do have some drain plug/valve options for you depending on what size you need. We have the Valterra Water Heater Drain Valve - 1/2" #A10-4003VP, the Valterra Water Heater Drain Valve - 1/4"…

view full answer...

Answer 2

The Fan-Tastic Vent Ultra Breeze Trailer Roof Vent Cover - 23" x 19.5" x 10.25" - Smoke #FVU1500GR is the same translucent color of the Fan-Tastic Vent #FVK1020-19. This isn't so much a blue color as a gray color similar to sun…

view full answer...

Answer 3

In order to find the correct fit, you are going to have to do a little measuring. You will want to start by measuring the width of your current step assembly, followed by the height from step to step. After that, you will want to measure from the…

view full answer...

Answer 4

I added a photo which shows the location of the heating element of the Atwood Water Heater GC6AA-10E for you. It is item number 17 in the diagram. Atwood does recommend having a professional do the job if you are replacing it due to its location.

view full answer...

Answer 5

On your model Atwood Water Heater GC6AA-10E the electric heating element is located in the water tank in the back side of the water heater. The heater will have to be pull out of the RV to replace the unit. For a replacement you'd want #CAM02103.…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 9

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 10

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 11

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 12

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Replacement Element for Atwood GC6AA-9E Water Heater

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching