How To Obtain Grade 8 Bolts Used To Attach Curt Base Rails to Frame Brackets For a 5th Wheel Hitch

Question

Question:

Had my Q24 mounted with original hardware going to hotshot trucking Dot requires grade 8 carriage bolts do you have these?

asked by: Alan B

1

Helpful Expert Reply:

Yes, we have the grade 8 bolts that are used to secure the base rails to the frame brackets on a 5th wheel install kit. That said, we only offer these with the Replacement Hardware for Curt Universal 5th Wheel Installation Kit part # C16111 so that is what you need to use in order to obtain them.

expert reply by: Conner L

1

Answer 1

Your 2019 Grand Design Solitude is prewired for a Furrion Vision S Wireless RV Backup Camera System w/ Night Vision, part #FOS05TASF. This system comes with a 5" monitor that picks up the camera's signal wirelessly. They do not hook…

view full answer...

Answer 2

I spoke with my contact at Reese and he informed me that there is nothing you can adjust on the slider that will allow you to remove that play. He did say to make sure that the pull pins that attach the slider to the rails are in correctly. You…

view full answer...

Answer 3

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 4

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 5

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 6

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 7

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 8

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 9

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 10

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 11

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 12

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

How To Obtain Grade 8 Bolts Used To Attach Curt Base Rails to Frame Brackets For a 5th Wheel Hitch

Product Page this Question was Asked From

Continue Researching