Sliding Battery Tray for 8-1/2" x 12" Battery

Question

Question:

Do you make a sliding battery tray 8.5X12

asked by: Rick

0

Expert Reply:

The closest sliding battery tray we have available to the dimensions you listed is the Kwikee RV Battery Tray # LC366330, which measures 7-1/2 inches wide, 12-1/8 inches deep, and 2-1/2 inches tall. The next closest size up we have is the Kwikee # LC366485. This unit measures 14-9/16 inches wide, 15-1/2 inches deep, and 3-5/16 inches tall.

I have attached a short video review on this product that you can check out as well.

expert reply by: Chris R

0

Answer 1

The Kwikee RV Battery Tray - 14-9/16" Long x 15-1/2" Wide #LC366485 and Kwikee RV Battery Tray - 13" Long x 16-1/8" Wide #LC366357 are the closest we have to the battery tray you have on your 1997 Tioga RV.

view full answer...

Answer 2

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 3

Hi Mark; thanks for the question and I have some good news for you as we have the exact 5th wheel to gooseneck adapter to replace the Turning Point pin box on your Jayco Eagle HT 30.5 CKTS. The correct part is the following: - Gen-Y Hitch Shock…

view full answer...

Answer 4

Thanks for reaching out, Michael! The Dexter Electric Trailer Brakes #K23-086-087-00 are compatible with 3,500 lb axles and have the standard 4-bolt pattern so if that matches the specs of your axle then this will definitely work for your…

view full answer...

Answer 5

I have a solution for you, but you will need to know your battery size and determine how much space you've got in your battery compartment to help decide which Kwikee battery tray is going to work the best for you. The #LC366328 is…

view full answer...

Answer 6

We have a online diagram that will help you understand how the break away system is wired into your trailer. It is actually a simple installation. The system splices into the existing trailer wiring. The break away box will have 3 wires coming out…

view full answer...

Answer 7

Electric trailer brakes can work on a trailer that doesn't have a breakaway system. So the answer to your question is no, the breakaway battery would not affect how normal trailer brakes will operate under normal circumstances. The only time…

view full answer...

Answer 8

A diode like the part #RM-690 is a great idea but the only issue is that is has a max load of 85 amps. A standard 5,000 lb winch, like the ComeUp DV-5000si #CU645010, will greatly exceed the 85 amp rating of the diode so it would be useless. What you…

view full answer...

Answer 9

I checked with Kwikee and the distance from the very bottom of the Kwikee RV Battery Tray #LC366345 to the bottom of the sliding tray is 7/16 of an inch. I attached a diagram they sent me that has more dimensions of this as well.

view full answer...

Answer 10

To charge the battery in the Engager Trailer BreakAway Kit, #20099, you can attach the wire from the 12 volt circuit on the trailer side 7-Way (1 oclock position on the back of the trailer side 7-Way where the wires attach) to the input wire on the…

view full answer...

Answer 11

Typically people will let the breakaway battery run the breakaway system and then would use the accessory battery to power the interior lights etc. This tends to work the best since your breakaway battery needs to always be charged and interior…

view full answer...

Sliding Battery Tray for 8-1/2" x 12" Battery

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching