Parts Needed to Make a 7-Way Round Adapter to 6 Way Square Adapter

Question

Question:

how to go from a 7 way round truck to a 6 way square camper

asked by: Tim

0

Expert Reply:

To make a 7-way to 6-way square adapter will require you to get the part # 37995 to use the 6-way end and then wire up a 7-way round to it like part # PK11700. This will give you the adapter you would need since there isn't one already pre-made.

expert reply by: Jameson C

0

Answer 1

Since you have a battery on the trailer you will want to use something larger than a 4-Way connector. A 4-Way will only supply lighting on your trailer. It will not be able to provide a wire to charge your trailer battery. I would recommend to use…

view full answer...

Answer 2

If your trailer has a square 6-way connector I assume it has brakes. The other wire would perhaps be for a breakaway kit or interior lights on the trailer or a battery charger. If the trailer is setup with either of those functions, you will need to…

view full answer...

Answer 3

The only solution we are going to be able to provide for you is to build an adapter like you mentioned or do what most people do and replace the connector you have on your trailer with a standard 7-way so that it will work with your truck and most…

view full answer...

Answer 4

The easiest thing to do would be to replace the 6-Way square on the Jayco trailer with a 7-Way, #PK12706. You can adapt the 6-Way Jayco to the 7-Way on your vehicle. But it will take a little bit of work. First, you will need 6-Pole Square Trailer…

view full answer...

Answer 5

We do have 6-Pole Square Trailer Wiring Connector Kit (Car and Trailer Ends) #37995 that you can use for your Arctic Fox camper. This is both the male and female ends. But the wires on them are 18 gauge. You could replace the ground and power wires…

view full answer...

Answer 6

To make a 7-way to 6-way square adapter will require you to get the part #37995 to use the 6-way end and then wire up a 7-way to it like part #H20043. This will give you the adapter you would need since there isn't one already pre-made. Or you…

view full answer...

Answer 7

On the 6-Way square connectors #37995 they are more of a generic type of 6-Way square. The one in your picture looks like the infamous Jayco 6-Way like what is found on adapter #30104. But you need the opposite end from what is on this adapter. What…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Parts Needed to Make a 7-Way Round Adapter to 6 Way Square Adapter

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching