Replacement Threaded Hitch Pin for Swagman Original Bike Rack

Question

Question:

Will this fit the Swagman Original 3 64152?

asked by: Thomas M

0

Expert Reply:

Yes, the Threaded Hitch Pin # P5901 is the correct replacement for your Swagman Original Bike Rack # S64152-2. If you wanted to upgrade to a locking assembly you could use part # S64027, which features the same threaded design to reduce movement inside the hitch receiver but also has an integrated lock core and keys to help deter theft of your investments.

I have attached a short video review that you can check out as well.

expert reply by: Chris R

0

Answer 1

We have bike racks that have loading ramp options but the Swagman E-Spec part #S94FR does not have a loading ramp option and none of the ramps we offer would work with it. We have the Yakima OnRamp Bike Platform Rack #Y36FR or we have the Thule…

view full answer...

Answer 2

The Swagman Replacement Threaded Hitch Pin and Clip #P5901 is designed to fit Swagman bike racks with 2 inch shanks. This hitch pin actually has an outer diameter of 5/8 inch and is 4-3/4 inches long according to my contact at Swagman so it will not…

view full answer...

Answer 3

By locking bolt, I believe you mean the Threaded Hitch Pin and Clip #P5902, which came with the Swagman Trailhead #S63360. Also available is the Locking Anti-Rattle Threaded Hitch Pin #S64029 which locks the rack onto your vehicle instead of just…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 7

To me it makes the most sense to put a Bike Rack #HLY64FR on the flat towed vehicle rather than above the tow bars. Especially on heavy e-bikes as they are difficult to lift that high onto the rack, but also as it only makes sense to have the rack on…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Hey HPA, I would go with the Air Lift kit part #AL64VJ that fits your 2019 Toyota RAV4 based on what you described and your needs. This gives you adjustable support that you can tailor as needed so that you get the exact amount of support you need…

view full answer...

Answer 11

To add a hitch to your 2024 Toyota RAV4, I recommend the etrailer item #e23ZR. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a 4,000 lbs towing capacity, and a 600…

view full answer...

Answer 12

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...