Do Trailer Equalizer Heights have to be the Same to Level Trailer Leaf Spring

Question

Question:

building a trailer. ordered tandem hanger kit with 1 1/2inch front and rear hangers, with 2 1/2inch center hanger. put all in place on the frame and my spring seats and springs dont set level with the frame. appears that i need front and rear hangers same length as center, to level the springs. or is this normal? what do you think?

asked by: Trenton T

0

Expert Reply:

Hangers come in varying heights to accommodate equalizers that have different heights and different frame clearances but the end goal is to allow the leaf springs to sit as level as possible. The part # 115918 you referenced is the 2-1/2 inch height you are looking for but a different option might be to go with a different height equalizer.

I attached a link to a page that has all of the equalizers we carry as well.

expert reply by: Jameson C

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 5

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 6

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 7

To correctly measure a leaf spring, you'll want to jack the trailer up on jack stands so the axle is hanging freely, then measure directly across from the center of one spring eye to the other, as shown in the provided diagram. The height of the…

view full answer...

Answer 8

I definitely understand being a bit overwhelmed by the amount of options in front of you, however I can definitely help with differentiating the trailer hitches for your 2019 Subaru Outback Wagon along with explaining my personal recommendation,…

view full answer...

Answer 9

Well shackle length is mainly based on the height difference between the front and rear hangers. The rear hanger normally doesn't hang as low as the front so that the shackle can offset the difference and add the ability to move. What is the…

view full answer...

Answer 10

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Answer 11

Hey Doug, thanks for reaching out! The MORryde ALLTREK 4000 #MR89DR dimensions can be a bit difficult to explain via text so I've attached an image giving you the dimensions you're asking about!

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Do Trailer Equalizer Heights have to be the Same to Level Trailer Leaf Spring

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching