Is Draw Tite Hitch DT45519 Correct Fit for 2009 Chevy Silverado

Question

Question:

The frame on my 2009 silverado is 42. is this the right hitch?

asked by: Richard

0

Expert Reply:

Yes, the Draw Tite hitch part # DT45519 that you referenced is the correct fit for your 2009 Chevy Silverado with a 42 inch wide frame.

expert reply by: Jameson C

0

Answer 1

We haven't had the chance to install the Curt Class V Trailer Hitch Receiver #C15703 on the 2008 Chevy Silverado 2500 so I don't have exactly how far beneath the bumper the receiver will sit, however I did go out to our warehouse to take a…

view full answer...

Answer 2

The confusion is that the two answer pages have two different hitches they are referring to. The #C15312 measures 2-3/4 inches from the mounting flange down to the hitch opening and the #C15313 measures 5-5/8 inches. I attached a picture that has…

view full answer...

Answer 3

I went to the warehouse and measured the Curt Trailer Hitch Receiver, part #C15703. I have attached a photo of the trailer hitch and have noted the dimensions you can check out. This is a Class V trailer hitch and it has a 2-1/2 inch receiver…

view full answer...

Answer 4

I can tell you how far the Curt #C15400 extends out from the frame and you can use that to determine the measurement to the end of the service body. We don't have information on the RKI S6080 or a way to determine that distance otherwise. The…

view full answer...

Answer 5

Both of the Curt hitch receivers have the same bolt hole measurements. It's 9 inches from the first hole (Closest to the front of the truck) to the second hole and 5-1/2 inches from the second to the third. There's 39 inches across from hole…

view full answer...

Answer 6

I called my contact at Curt to confirm these measurements on the Curt #C15313 trailer hitch for you. The width of the hitch from center to center of the bolt holes measures 38-7/8 inches. The top of the receiver to the mounting holes measures 5-7/16…

view full answer...

Answer 7

I had our warehouse measure the Curt Trailer Hitch Receiver #C15703 you were looking at, and has an overall width of 40-5/8", overall length of 29". The distance between the vertical mounting holes is 14-1/2" center to center, and the…

view full answer...

Answer 8

The best class V hitch for your 2002 Silverado 2500 is going to be the Curt Trailer Hitch item #C15703. This hitch is custom fit for the 2500 HD's with the 6-1/2' beds and bolts to your truck with included hardware. This hitch has a…

view full answer...

Answer 9

Curt Trailer Hitch Receiver #C15703 hangs pretty low on a 2005 Chevy Silverado 2500. From the bottom of the bumper to the top of the hitch receiver it is approximately 4 inches. I have included a picture showing the gap. A similar hitch, #C15302,…

view full answer...

Answer 10

We offer Class V hitches in both 2-inch and 2-1/2-inch sizes for your 2009 Chevrolet Silverado 2500. All are shown on the linked page. Draw-Tite's 2-inch hitch #41944 is a no-drill install since it bolts up to the bumper bracket the same way as…

view full answer...

Answer 11

The Draw-Tite #DT45519 is designed to be used on the 8 foot bed models of the GMC Sierra and will not fit the short bed models. That being said, we do have Class V hitches with a 2 1/2 inch receiver options available for your short bed truck. The…

view full answer...

Answer 12

I spoke to my contact at Curt and he informed me that the Curt hitch #C15317 center section measures 31-5/8 inches. The center to center mounting hole width with the flanges attached is 34-7/8 inches. He also informed me that the flanges on the…

view full answer...