Width of Channel for Titan 2-Tang Clevis w/ 3-Position Adjustable Channel

Question

Question:

Hello, what is the overall width of the channel. I know the height just not the width. Thanks!

asked by: Josh

0

Expert Reply:

The inner width of the Titan 2-Tang Clevis w/ 3-Position Adjustable Channel # T0909500 is about 3" while the outer width is about 3-5/8". I have attached a photo to demonstrate this.

expert reply by: Jon G

0

click to enlarge

Answer 1

Based on the hub picture, you have what they refer to as Utility hubs and will need the Dexter Nev-R-Adjust Electric Trailer Brake Kit - 12" - Left and Right Hand Assemblies - 7K #23-464-465. These brake assemblies will allow you to adjust only…

view full answer...

Answer 2

It sounds like you're looking for a clevis hitch, like the MaxxTow #MT70034. Then use a 1 inch diameter clevis pin, part #CP20, to hook up your trailer.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

I would use a protractor, see photo, place the protractor on the edge of the inside of one side of the trailer frame and the other inside edge of the trailer frame should be parallel with the 50 degree line on the protractor. Another way to verify…

view full answer...

Answer 5

The only differences between the Demco Trailer Coupler #DM14976-52 and #DM88XR are the colors and the mounting bracket design. The part DM14976-52 is silver and has a straight, or no-drop, design with the bottom of the coupler being towards the top…

view full answer...

Answer 6

The Bulldog Winch Standard Series Off-Road Winch #BDW10041 could work well on your car hauling trailer, though it is designed as a recovery winch, but it ultimately will depend on the types of loads you plan on carrying if the winch is the right one…

view full answer...

Answer 7

The mounting holes are 2 inches on center for the clevis and 3 inches on center for the mount. The clevis and side of the bracket has holes that are 0.64 inch. The top and bottom holes of the mounting bracket are 0.48 inches and the center hole is…

view full answer...

Answer 8

The diameter of the mounting holes of the #T0897900 are 5/8 inch. We also have this as a kit with the channel and mounting bolts/nuts with part #T1812200.

view full answer...

Answer 9

I recommend the Buyers Products 4" Standard Bolt-On Trailer Winch #3371903020 for your trailer. This has the same mounting bracket as the Titan Chain Lashing Winch #TCLR965 you found. The Buyers winch has 2-1/2" of space between the frame…

view full answer...

Answer 10

I had the Demco 2-Tang Clevis - Adjustable Channel Mount #DM05593-97 measured and from end to end, it will be 9 1/4 inches long.

view full answer...

Answer 11

I spoke with my contact over at Demco about clevis #DM05593-97. The squares at the back are 1.88 inches square. And the space between the upper and lower tangs is 2 inches. I have included a picture showing these measurements for you.

view full answer...

Answer 12

Torque specs for wheel lug nuts will vary depending on the diameter of the lugs, type of lug nut and the wheel's material. The linked chart details the recommended torque for many combinations. Dexter Hub/Drum #84546UC3 has 1/2-inch studs and…

view full answer...

Width of Channel for Titan 2-Tang Clevis w/ 3-Position Adjustable Channel

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching