LED Replacement Lamps for Wesbar 40326 on 2003 Ranger Trail Boat Trailer

Question

Question:

I would like to replace my tail lights and side markers on my 2003 rangertrail trailer with led lights. The existing lights are wesbar 102640 any help would be appreciated.

asked by: Toby

0

Expert Reply:

Optronics makes an LED lamp that's a direct replacement for the Wesbar 102640. You'll want to go with Optronics # TLL160RK. The lamps are submersible and use just a fraction of the power of a comparable incandescent trailer lamp. This part includes both the driver's and passenger side lamps.

If you click the provided link, you can see a product description video featuring the lamps I recommended.

expert reply by: Mike L

0

Answer 1

What you have is a 5-way with a double wishbone, which means it is likely a double wire for marker lights as well as a double ground. You can replace your 5-way with another wishbone-style but it does not need to be a double wishbone with 7 wires,…

view full answer...

Answer 2

I have a solution that may work for you, but we do not currently have any 3" diameter submersible reverse lights. Have a look at the Optronics Backup Light #BU45CB which is a 4-1/4" diameter light that can be mounted to your trailer using…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 8

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 9

Typically 4-way wiring consists of 18 and 16 gauge wires. For a 4-way that has all 16 gauge wire you would want the Wesbar 4-Pole Flat Connector #W787264. The part #HM38138 uses 18 gauge for all wires but the white that uses 16 gauge.

view full answer...

Answer 10

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 11

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 12

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...