Replacement 5-Way Flat Wiring for 2005 Four Winns Trailer

Question

Question:

Id like to replace the wiring on my 2005 Four Winns trailer that has the blue wire for the brake actuator for backing up. What would I need?

asked by: Dennis J

0

Expert Reply:

I recommend using the 5-Pole Flat Connector # A40W5Bto rewire your 2005 Four Winns trailer. This is a wishbone style so you can easily route the wiring to each side of your trailer. The regular lighting harness is 40' long while the ground wire is 4' long and the blue wire for the reverse light function is 5' long.

expert reply by: Jon G

0

Answer 1

Hey Ryan, yeah you're right TDE is no longer a thing and unfortunately we don't carry a replacement reverse solenoid for that actuator so at this moment your best bet would be to replace the entire thing with the Dexter DX7.5L A-60…

view full answer...

Answer 2

I recommend replacing your Fulton T1801 boat trailer winch with the Dutton-Lainson Hand Winch #DL17042. Fulton was acquired by First Brands in the beginning of 2023 and has had issues with manufacturing of parts including those for your Fulton…

view full answer...

Answer 3

The Dexter drop-n-go #099-175-20 would definitely have the same capability as your TDE actuator, provided it is a disc brake setup. TDE is no longer in business so I'm afraid finding a direct replacement will be impossible. My main concern is…

view full answer...

Answer 4

We have the Dexter DX7.5L A-60 Brake Actuator w Electric Lockout #DX29FR for disc brakes and the Dexter DX7.5L A-60 Brake Actuator #DX27FR for drum brakes. These will have similar bolt patterns as the Tie Down Engineering LP7000 actuators we have…

view full answer...

Answer 5

If you are wanting to replace the entire surge brake actuator on your Four Winns Horizon 190 boat trailer then I have exactly what you will need. I recommend using the Dexter Disc Brake Actuator part #099-175-20. This actuator works with…

view full answer...

Answer 6

It sounds as though there is a short or something is mis-wired. Using a circuit tester, like the #PTW2993, check the connection points in the vehicle side connector, to see if there is constant power on the running light circuit (brown wire on the…

view full answer...

Answer 7

I'm guessing it is approximately 3-3/8" across if you measured it. Unfortunately there are no options that will slide in because it won't line up correctly, and everything is designed to fit a 3" tongue so it is too wide to mount an…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 10

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 11

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Replacement 5-Way Flat Wiring for 2005 Four Winns Trailer

Product Page this Question was Asked From

Continue Researching