Will RockyMounts WestSlope 2 Bike Rack Fit 2019 Subaru Legacy with Curt Hitch Installed

Question

Question:

With the part that fits into the hitch clear the bumper when it curves up on a 2019 Subaru Legacy. The hitch is slightly recessed. It’s a Curt 2 inch class III. If not, is there another platform rack the folds up like this one you would recommend.

asked by: Quintin

0

Expert Reply:

Thank you for the picture of the Curt hitch # C12290 you have installed on your 2019 Subaru Legacy. Based on that we know that the RockyMounts WestSlope 2 Bike Rack # RKY10222 will easily fit as there's plenty of clearance on this rack to clear the rear bumper.

expert reply by: Jameson C

0

click to enlarge

Answer 1

I went out to the warehouse to take a look at the Draw-Tite Class II Trailer Hitch #36493 referenced in your question. I measured a distance of right at 9 inches from the top of the bracket where it will mount to the vehicle to the bottom of the…

view full answer...

Answer 2

The installation of a trailer hitch on your 2017 Subaru Legacy will require the trimming of the heat shield. I have added a cut out of the linked instructions of Draw-Tite trailer hitch #36493 that fits your '17 Legacy so you can see what will…

view full answer...

Answer 3

Installing a trailer hitch like the Curt Class II Trailer Hitch Receiver #C12136 on your 2016 Subaru Outback can effect your vehicle's ground clearance at the rear. The cross tube of the trailer hitch will sit below the vehicle, as seen in the…

view full answer...

Answer 4

I would be happy to help you find a hitch and a bike carrier for your daughter's 2015 Toyota Camry. I would recommend the Draw-Tite Trailer Hitch Receiver item #36540 you referenced. This hitch is custom fit and bolts directly to your Camry with…

view full answer...

Answer 5

It looks like we have tested the Thule T2 Pro XTR 2 Bike Platform Rack part #TH83JV on a few different Toyota Siennas. It looks like both times when the rack was titled back, it did not make contact with the ground. Granted, this would vary depending…

view full answer...

Answer 6

I have a bike rack solution that might be better for your needs, but you can't tilt the Thule Apex XT part #TH9026XT with bikes loaded. The anti-sway cradles of the rack would not be able to support the bike weight at that angle. Instead check…

view full answer...

Answer 7

I really like the Saris SuperClamp EX part #SA4025F for ground clearance. It has a decent rise in the shank at 5 inches (which is a couple more inches than most racks) and the bikes are held pretty close together which means less of an angle that can…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 11

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 12

To add a class III hitch to your 2024 Honda CR-V hybrid, I recommend the Curt Trailer Hitch item #C13397. This hitch is custom fit and bolts to your CR-V with included hardware. It is a class III hitch with a 2" receiver. I really like this…

view full answer...