Identifying 12 Volt Power Circuit Wire on 7-Way of Truck

Question

Question:

Hi, can you tell me which wire on this harness represents the charge wire to my fifthwheel house battery? Im hoping blue, white or red the 12g wires.....Thanks

asked by: Corey H

0

Expert Reply:

The red wire in the picture you submitted is the 12 volt charge circuit that is charging the battery. The white is the ground and the blue is brake output.

expert reply by: Jameson C

0

click to enlarge

Answer 1

I checked out the link you attached and the easiest solution we have that's similar is the part #41157 which is a 5th /gooseneck wiring kit that you could use as a way to get just the reverse light circuit.

view full answer...

Answer 2

Most if not all trailer wiring harnesses/connectors use larger wires for the 12 volt and ground circuits compared to the other circuits (lights). The sockets themselves don't have an amperage rating so you will go by the draw of the things…

view full answer...

Answer 3

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

There is not a plug and play adapter for your Lance connector that we are aware of. Typically this is installed by the Lance dealer. A junction box/7-way plug kit like #HS381-9000 is an option you have to convert the camper to match the 7-way RV…

view full answer...

Answer 6

Thanks for the photo, that was a big help. And the answer is yes, your 2023 Ford F-350 Cab & Chassis is 100 percent compatible with the Curt 7-way: - Curt T-Connector Vehicle Wiring Harness for Factory Tow Package - 7-Way Trailer Connector #C69CR…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

Yes, you can and it'll allow you to keep the one on your bumper. I recommend the Curt 5th Wheel/Gooseneck Custom Wiring Harness w/ 7-Pole Connector item #C57010. This harness puts a 7-way connector in the bed of your 2024 Ford F-250 and makes…

view full answer...

Answer 9

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...

Answer 10

We do have a wiring diagram for you! Whether you have the 1,000 psi Dexter DX Series #K71-650 or the 1,600 psi Dexter DX Series #K71-651 the wiring will be the exact same. I have attached a wiring diagram and review videos for you to check out. Just…

view full answer...

Answer 11

You will need the Curt T-Connector Vehicle Wiring Harness #C69CR to plug into the factory connectors on your 2021 Ford F-450 cab and chassis flatbed. This will then allow you to use the Hopkins Endurance 5th Wheel/Gooseneck 90-Degree Wiring Harness…

view full answer...

Identifying 12 Volt Power Circuit Wire on 7-Way of Truck

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching