Will the Stromberg Carlson Rail Mate Work On a Forest River Rockwood Mini Lite with Flexco Steps

Question

Question:

I have 2016 Rockwood minilite 2504s with 3 step manual Flexco steps. Will Rail Mate fit?

asked by: John W

0

Expert Reply:

Yes, the Stromberg Carlson Rail Mate Folding Handrail part # AP-101 will work just fine with the Flexco Manual Folding Triple Steps on your 2016 Forest River Rockwood Mini Lite 2504S. It comes with all of the hardware and brackets you need for installation along with a set of instructions for this process.

expert reply by: Conner L

0

click to enlarge

Answer 1

When driving the Stromberg Carlson Rail Mate Folding Handrail #AP-101 would need to get removed from the outside of the RV.

view full answer...

Answer 2

The Brophy Camper Scissor Steps for truck campers, #AS04, are intended for an entry height of 31" to 40". If your camper door sets within that 31-40' range then yes this will fit your rig. Please see attached image for measuring points…

view full answer...

Answer 3

The top of the Rail Mate folding handrail #AP-101 is not attached to anything. The mounting brackets that hold the rail are only attached to the steps because the hand rail part is meant to be removable and the brackets are not.

view full answer...

Answer 4

The Stromberg Carlson Rail Mate #AP-101 is intended for left hand mount. All 3 Brophy Handrails #AHR3 for 3-step scissor steps, #AHR4 for 4-step, and #AHR5 for 5-step can all be mounted on either side of the stairs. All 4 products are made to fit…

view full answer...

Answer 5

Yes the Stromberg Carlson removable hand rail part #AP-101 would fit your 2020 Sportsman Travel Trailer Model 260BHSE.

view full answer...

Answer 6

The Brophy Camper Scissor Steps #AS04 actually come with a bracket for you to mount on your pickup. It allows you to easily install the steps when you reach your destination and then remove them before heading out! If you would like to add a handrail…

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 10

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 11

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 12

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...