Drill Bit Tap for Weld Nut for Trailer Hitch Installation on 2014 Dodge Charger

Question

Question:

Need to clear the thread on the frame of car what size tap do I need

asked by: Antonio T

0

Expert Reply:

I believe the part you are talking about is the weld nut on your 2014 Dodge Charger where the M12 bolt for the Draw-Tite Trailer Hitch # 76145 installs. For this you need a12 mm x 1.25 tap and drill bit.

expert reply by: Jon G

0

click to enlarge

Answer 1

The etrailer Trailer Hitch Receiver part #e98846 is a fit for the following vehicles: 2008 - 2020 Nissan Rogue 2010 - 2011 Nissan Rogue excluding Krom 2014 - 2015 Nissan Rogue Select Please note, trailer hitches are vehicle specific so they only…

view full answer...

Answer 2

In regards to the Draw-Tite Max-Frame Trailer Hitch Receiver part #76145 which is a confirmed fit for a 2018 Chrysler 300 (All Models), the mounting holes are about 41" apart on center which I think is what you are asking for. If not,…

view full answer...

Answer 3

I have two options that will allow for you to securely attach a cooler to your Curt Cargo Carrier part #C18151. You can choose from either a cargo net or a set of cambuckle ratchet straps. A cargo net such as the Curt Stretchable Cargo Net part…

view full answer...

Answer 4

The install hardware for the #75270 that your referenced is M12 X 1.25 X 35mm. I attached a help articles on cleaning out weldnuts for you to check out as well.

view full answer...

Answer 5

For the video on the Curt Class III hitch receiver for 2007 Honda Odyssey, Part #C13068, as you noted we did not happen to include the measurement of the distance from the ground to the top of the installed receiver, as we did for the Draw-Tite…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

The ground clearance for the Draw-Tite Max-Frame Trailer Hitch Receiver part #76145 on your stock 2019 Dodge Charger RT is about 8-1/2 inches from the lowest point of the hitch (the bottom of the safety chain loops) to the ground. In the image I…

view full answer...

Answer 8

I have included a picture showing what Curt trailer hitch #C13236 looks like installed on a 2017 Dodge Charger. I think that the hitch and its positioning match the lines of the vehicle quite well which is not normally the case with trailer…

view full answer...

Answer 9

The Draw Tite hitch part #76145 that you referenced which fits your 2014 Chrysler 300 does have a 675 lb tongue weight rating so it would have the needed capacity for your chair setup but you'd need to verify that your vehicle also has the…

view full answer...

Answer 10

When we installed the Draw-Tite Max-Frame Trailer Hitch Receiver #76145 on a 2018 Dodge Challenger we found that from the ground to the top of the inside of the receiver measured 9-1/4" as you can see in the attached photo. It might be a little…

view full answer...

Answer 11

For a 2013 Dodge Charger you can use #118560 to add a trailer wiring harness. The other option is to use #C56135 from Curt. I have included a link to the installation instructions for this harness for you.

view full answer...

Answer 12

For a 3-bike platform rack the Kuat Transfer part #KU24FR would be a great option. We had the chance to test fit this rack on a similar 2015 Chrysler 300 and it fit and worked well. Check out the review video I attached that shows this. Platform bike…

view full answer...