3 Inch Waste Valve for Black Water Tanks with a Removable Handle

Question

Question:

Does the handle unscrew? I need to thread on an extension rod with handle.

asked by: George

0

Expert Reply:

We do have a 3 inch diameter black water waste valve with a handle that unscrews but part # T1003VPM doesn't have a removable handle. Instead use part # 34439240 from LaSalle Bristol.

Additionally, use part # 34466SP1112 for a 12 inch extension.

expert reply by: Charles S

0

Answer 1

I spoke to a Valterra representative and I was told that they do not offer a sleeve to slide over the two shafts to join them together. If the male thread has broken in the handle, and the coupler is still in working order, you may be able to use…

view full answer...

Answer 2

I can't be sure how the end of the rod at the blade of the valve is attached. If the handle and rod we can see turn freely, then I would turn the rod clockwise to see if you can get it to thread into something. I am going to guess that yanking on…

view full answer...

Answer 3

In general all black water waste valves are the same size and the Valterra Waste Valve Body #T1003PBC that you referenced woudl fit and work well as this is the standard 3 inch size. The thickness is 5/8 inch and the hole spacings are 3-3/4 inches.

view full answer...

Answer 4

Sounds like instead you would want the part #T1003VP which is a similar valve as the #T1003PBC except it comes with the T handle. The part is ABS plastic, so you could use an ABS sealant or glue. The glue is not included though. Part number #A05-0303…

view full answer...

Answer 5

The Double RV Waste Valves - Elbow - Rotating - 3" and 1.5" Hubs to 3" Lug #T80 will use the Valterra RV Sewer Spigot with Flange - 1-1/2" #T1005-1 to match the original hub. This secures to your pipe with solvent #A05-0303. The…

view full answer...

Answer 6

Yes, the handle of the Valterra waste valve, part #T1003VP, does unscrew so it can be replaced or extended. We have several different lengths of extended rods that fit: 8 inches, #TX8HPB 9 inches, #TX9HPB 24 inches, #TX24HPB 32 inches, #TX32HPB 36…

view full answer...

Answer 7

Yes, if you were to remove the hub and spigot from the Valterra Bladex Waste Valve #T40NH you would be left with a Valterra Bladex Waste Valve Body #T1003DSPB with the threaded shaft rather than a drilled shaft. A better option may be to use the…

view full answer...

Answer 8

The best option for you to use the Valterra Bladex Waste Valve part #T40B would be to add the Extension Rod part #T1046-12VP for 6" - 11" or part #TX36HPB for 36". I cannot confirm that the handle on your Thetford valve will work with…

view full answer...

Answer 9

The four bolt pattern of the flange on the waste water valves is an industry standard so you don't really have to worry about measuring the bolt hole spacing. However, to address your specific question the bolt holes are spaced 3.73" apart…

view full answer...

Answer 10

In my experience Valterra has been MUCH easier to get in contact with and get parts from than LaSalle Bristol. Dometic is the parent company for Valterra and typically has pretty good customer service every time I've called them. It's a bit…

view full answer...

Answer 11

Hey Wyatt, so we have a hose that was designed to be used with the #T01-0091VP with the part #W01-4180 which does have a different thread size. This is intentional so that someone doesn't use a standard garden hose that someone might attempt to…

view full answer...

Answer 12

I see what you mean about the cover being "recessed" into the front of the trailer. After looking thru a few pictures of these 2005 Trail Lite Hybrid trailers, it appears to be a fairly unique tank cover. I am sorry to say that we do not…

view full answer...

3 Inch Waste Valve for Black Water Tanks with a Removable Handle

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching